top of page

ISO 3035
Flat Crush Resistance of Corrugated Fibreboard

ISO 3035 Guided Crush Platens for Corrugated Fibreboard by Universal Grip

Downloads: ISO 3035 Guided Crush Platens for Corrugated Fibreboard – Universal Grip Data Sheet (PDF)

Written by Chris Thomas, Universal Grip Company · Reviewed by Frank Bertini · Updated October 27, 2026

ISO 3035 is the international method for measuring the flat crush resistance of corrugated fibreboard, the test the packaging industry calls FCT. A circular test piece of single-wall or single-faced board is compressed between two parallel platens, perpendicular to its surface, until the flutes collapse. The maximum force divided by the test piece area, reported in kilopascals, tells you how rigid the fluting is and whether it was crushed during corrugating, converting or handling.

Corrugator QC labs, box plants, packaging designers and paper mills that supply corrugating medium all run the test. This guide covers the current ISO 3035:2025 edition, specimen preparation, the test machine and platens, a step-by-step procedure, a worked calculation, how to read the force curve, and how the method compares with TAPPI T 825. Universal Grip supplies a guided four-post crush platen set built for ISO 3035 work; it is described in the equipment section below.

In this guide: What ISO 3035 Measures · ISO 3035 Editions and Scope · Test Pieces: Size, Number, Sampling and Conditioning · Apparatus: Fixed-Platen Compression Tester and Platens · ISO 3035 Test Procedure Step by Step · Calculation and Worked Example · Reading the Force Curve: Valid and Invalid Results · Common Errors and How to Avoid Them · ISO 3035 vs TAPPI T 825 and Related Standards · ISO 3035 Equipment from Universal Grip · FAQ

What ISO 3035 Measures

Flat crush resistance is the maximum force a corrugated board test piece sustains, applied perpendicular to its facings, before the flutes collapse, divided by the area of the test piece. The result is a pressure, expressed in kilopascals (kPa, which is the same as kN/m²).

Unlike edge crush or box compression, the flat crush test isolates the fluted medium. The liners only carry the load into the flutes, so the result is governed by:

  • The strength and grammage of the corrugating medium

  • Flute profile and flute height: smaller flutes have more flutes per unit length and usually give higher flat crush values

  • Flute formation quality on the corrugator, including leaning or uneven flutes

  • Damage done after corrugating: nip pressure in printing and die-cutting, pull-roll crush, tight stacking or rough handling

  • Moisture content of the board at the time of test

Because the flutes are the part of the board most easily damaged during converting, FCT is mainly a flute rigidity and process-damage indicator. A board that tested well off the corrugator and poorly after printing has had its flutes crushed. Flat crush is not a direct predictor of stacking strength; box compression strength is driven mainly by edge crush resistance (ISO 3037) and box geometry. Crushed flutes do lower stacking strength, though, because they reduce board thickness and bending stiffness, which is why FCT and caliper are often checked together.

ISO 3035 Editions and Scope

The current version is ISO 3035:2025, the fourth edition, published in July 2025 by ISO/TC 6/SC 2 in collaboration with CEN/TC 172. It cancels and replaces ISO 3035:2011 (third edition), which in turn replaced the 1982 second edition. Europe adopted the new edition as EN ISO 3035:2025, so national versions such as BS EN ISO 3035 and DIN EN ISO 3035 carry the same text.

What changed in 2025

  • The note in clause 5.1 was deleted because beam-deflection compression testers are no longer within the scope of ISO 13820:2021. The method now assumes a fixed-platen, motor-driven tester.

  • A dedicated Precision clause was added.

  • Precision data from Cepi-CTS (the European paper industry's comparative testing service) were updated.

The 2011 edition had already tied the instrument to ISO 13820, defined the relevant terms and added the first precision statement. If your specification still cites ISO 3035:2011 or the older EN ISO 3035 / EN 23035 references, the test principle is the same, but confirm which edition your customer expects.

Scope

  • Applies to single-faced and single-wall (double-faced) corrugated fibreboard used in the manufacture of shipping containers.

  • Does not apply to double-wall (double-double-faced) board: the middle liner shifts and the two flute layers collapse at different loads, so there is no clean end-point.

  • Does not apply to microflute board, for the same reason: the end-point is not clearly defined or observable.

Normative references in the 2025 edition are ISO 186 (sampling), ISO 187 (conditioning and testing atmosphere) and ISO 13820:2021 (description and calibration of fixed-platen compression-testing equipment).

Test Pieces: Size, Number, Sampling and Conditioning

ISO 3035 uses circular test pieces cut with a circularly guided knife that leaves clean edges perpendicular to the facings. A circle avoids corner effects and lets the flutes collapse evenly. The two sizes in common use for ISO 3035 work, and the sizes commercial ISO 3035 cutters are made for, are:

  • 100 cm² (10,000 mm²): diameter 112.8 mm, the usual size for single-wall board

  • 50 cm² (5,000 mm²): diameter 79.8 mm, used where a smaller piece or lower peak force is needed

Whatever size you use, record the actual area and use it in the calculation. A 1 mm error in diameter on a 100 cm² piece changes the area by almost 2 %, so check cutter dimensions periodically.

Specimen preparation rules

  • Sample according to ISO 186 so the test pieces represent the lot.

  • Cut away from score lines, printing, glue joints, die-cuts and handling marks. Printed areas have often passed through a nip and give lower values.

  • Never crush the edges while cutting. Dull blades and press-type cutters that pinch the board are a common source of low results.

  • Handle test pieces by the edges and do not stack weight on them before testing.

  • Plan on at least 10 valid test pieces per sample, the customary minimum in ISO 3035 practice and in the related FEFCO and TAPPI methods. Cut a few spares to replace pieces rejected for leaning flutes.

Conditioning

Condition and test in the ISO 187 standard atmosphere: 23 °C ± 1 °C and 50 % ± 2 % relative humidity. ISO 187 also describes preconditioning on the dry side so that every test piece reaches equilibrium from the same direction, which reduces moisture hysteresis. Paper fibers soften quickly as moisture rises, so testing straight off a cold dock or a humid warehouse can shift results by more than the difference you are trying to detect.

Apparatus: Fixed-Platen Compression Tester and Platens

ISO 3035 requires a motor-driven, fixed-platen compression tester that meets ISO 13820:2021. Fixed-platen machines compress at a constant rate of strain, meaning the platens close at a constant speed regardless of force. Older beam-deflection crush testers, where the load is applied through a deflecting beam, are no longer covered.

The test can be run on a dedicated crush tester or on a universal testing machine fitted with suitable compression platens. For corrugated board, a benchtop universal testing machine in the 5 kN class covers most single-wall boards. What matters for the platens:

  • Flat, rigid, parallel platens larger than the test piece, so the whole surface is loaded evenly

  • Very low lateral movement of the moving platen: if the upper platen can shift sideways, the flutes lean instead of crushing straight down and the peak drops

  • A rigid load path, so the platens do not tilt as the force peaks

  • A load cell sized to the expected peak; a 100 cm² piece of single-wall board typically peaks in the low kilonewton range

ISO 13820 sets the detailed calibration requirements for platen condition, speed and force measurement. For a sense of the tolerances involved, TAPPI T 825 requires platens parallel within 1 part in 2000 (50 µm over 100 mm) and lateral movement of no more than 0.050 mm. Guided platens, where the moving platen runs on posts and bushings, are the usual way to hold that geometry on a universal testing machine.

Test speed

The platens close at 12.5 mm/min ± 2.5 mm/min, the standard rate for fixed-platen corrugated board testers. Some summaries quote ±0.25 mm/min; that tighter tolerance belongs to TAPPI T 825, not ISO 3035. Running on a universal testing machine, simply set the crosshead to 12.5 mm/min.

ISO 3035 Test Procedure Step by Step

  • 1. Check the tester: verify the speed setting, zero the load cell with the platens open, and confirm platen faces are clean and free of fibers or adhesive.

  • 2. Cut the conditioned board into circular test pieces of known area in the test atmosphere, avoiding prints, scores and damage.

  • 3. Measure board caliper if you track flute damage (ISO 3034 covers single-sheet thickness of corrugated board).

  • 4. Open the platens to a gap comfortably larger than the board thickness.

  • 5. Place the test piece centrally on the lower platen. Off-center pieces load unevenly and tend to roll.

  • 6. Start the platens at 12.5 mm/min. Many labs apply a small contact threshold so the trace starts cleanly at first contact.

  • 7. Continue until the flutes have clearly collapsed. The software records the force-deflection curve.

  • 8. Record the maximum force sustained before collapse (Fmax).

  • 9. Inspect the crushed piece. Note any test piece in which the flutes leaned or rolled over sideways instead of collapsing symmetrically.

  • 10. Repeat until you have at least 10 valid results, then calculate the mean and standard deviation.

Note: Keep the test pieces in the conditioned atmosphere until the moment of test. A stack of cut circles left on a bench by a sunny window or HVAC vent will drift in moisture content within minutes.

Calculation and Worked Example

Flat crush resistance for each test piece is:

FCT = Fmax / A, where Fmax is the maximum force in newtons and A is the test piece area in square meters. N/m² is pascals, so divide by 1,000 for kPa.

A shortcut: force in newtons divided by area in cm² gives N/cm², and 1 N/cm² = 10 kPa.

Worked example: C-flute single-wall board, 100 cm² test pieces

  • Test piece area: 100 cm² = 0.0100 m²

  • Ten Fmax values (N): 2410, 2530, 2380, 2470, 2550, 2440, 2390, 2500, 2460, 2420

  • Sum of forces: 24,550 N, so mean Fmax = 2,455 N

  • First test piece: 2,410 N ÷ 0.0100 m² = 241,000 Pa = 241 kPa (check: 2,410 N ÷ 100 cm² = 24.1 N/cm² = 241 kPa)

  • Mean flat crush resistance: 2,455 N ÷ 0.0100 m² = 245,500 Pa ≈ 246 kPa

  • Standard deviation of the ten results: about 5.8 kPa; coefficient of variation about 2.4 %

With 50 cm² test pieces the force roughly halves for the same board: a peak of 1,180 N on 0.00500 m² gives 236 kPa. Results from different test piece sizes are in the same units and can be compared, but record the size in the report because edge effects are proportionally larger on smaller pieces.

For context, the interlaboratory study behind TAPPI T 825 used C-flute single-wall boards in roughly the 207 to 276 kPa range, so the example sits in a realistic band. Smaller flute profiles generally test higher than C-flute because they have more flutes per unit length.

Report the mean and standard deviation, the number of test pieces, the test piece area, the conditioning atmosphere and any pieces rejected or noted for leaning flutes.

Reading the Force Curve: Valid and Invalid Results

A good flat crush curve rises steeply and roughly linearly as the flutes are loaded, rounds over as the flute walls begin to buckle, peaks, and then drops sharply as the flutes fold. After the drop, force climbs again as the collapsed medium and liners compact. Only the first peak, the maximum force before collapse, is the flat crush value. The rising force after collapse is just the board being squashed flat and must not be read as the result.

Patterns to watch for

  • Leaning or rolling flutes: the flutes tip over sideways like dominoes instead of crushing straight down. The peak is low and the piece shows a skewed collapse. Note these pieces; a high proportion points to poor flute formation or a platen with lateral play.

  • Multiple small peaks before the main collapse: flutes of slightly different heights take the load in sequence. Pronounced stepping suggests uneven flute height or partial pre-crush.

  • Low initial slope and rounded peak: often a sign of flutes already damaged in converting. Compare against board sampled before the printer or die-cutter.

  • Very low values on one edge of a sheet: check corrugator nip settings or stacking damage on that side.

  • Unexpected spread between test pieces: suspect edge crushing at the cutter, mixed sample locations or conditioning problems before suspecting the board.

Note: The ISO 3035 scope excludes double-wall and microflute board precisely because their curves do not show a single, clear collapse point. Testing them anyway produces a number, but not one the standard recognizes.

Common Errors and How to Avoid Them

  • Wrong tolerance or speed: set 12.5 mm/min. A constant-force-rate setting or a beam-deflection tester gives different values.

  • Platens with lateral play: an unguided upper platen on a flexible load string lets flutes lean. Use rigid or guided platens.

  • Crushed edges from the cutter: inspect the cut edge; flutes should be open right to the rim.

  • Area not measured: a worn or mis-set cutter makes every result wrong by the same percentage.

  • Testing printed or scored areas: these regions have been through a nip and test low.

  • Reading the post-collapse rise: some software reports the overall maximum. Make sure the reported value is the first collapse peak.

  • Unconditioned board: moisture changes FCT strongly. Condition per ISO 187 and test in the same atmosphere.

  • Mixing TAPPI and ISO settings: specimen areas, speed tolerances and reporting differ. Run the method your customer specifies and say which one in the report.

ISO 3035 vs TAPPI T 825 and Related Standards

There is no ASTM flat crush method for corrugated board. In North America the counterpart is TAPPI T 825 (Flat crush test of corrugated board, rigid support method), currently T 825 om-24. Both methods compress a single-wall or single-faced test piece between rigid parallel platens at a nominal 12.5 mm/min and report maximum force per unit area. The differences are in the details:

  • Speed tolerance: TAPPI T 825 specifies 12.5 ± 0.25 mm/min; ISO 3035 allows ±2.5 mm/min.

  • Test piece area: TAPPI T 825 lists 32.3 cm², 50.0 cm² or 64.5 cm² (5, 7.75 or 10 in²), circular preferred; ISO 3035 work typically uses 100 cm² or 50 cm² circles.

  • Conditioning: TAPPI T 402 versus ISO 187; both test at 23 °C and 50 % RH.

  • Units: TAPPI allows kPa or psi (1 psi = 6.895 kPa); ISO reports kPa.

  • TAPPI T 825 asks you to report the number of specimens showing rolling failure.

TAPPI also has T 808, a flexible-beam flat crush method. TAPPI states that T 808 and T 825 do not produce similar results, which mirrors ISO's move away from beam-deflection testers in the 2025 edition. Do not mix results from rigid-support and beam testers in one data set.

Related corrugated board standards

  • ISO 3037: edgewise crush resistance (ECT), the main input to box compression estimates

  • ISO 7263: flat crush resistance of corrugating medium after laboratory fluting (the CMT test), which tests the raw medium rather than combined board

  • ISO 12192: ring crush of paper and board

  • ISO 12048: compression and stacking tests of complete, filled transport packages (box compression)

  • ISO 13820: description and calibration of fixed-platen compression testers used for all of the above

  • ISO 3034: single-sheet thickness of corrugated board, useful alongside FCT for detecting flute damage

  • ISO 186 and ISO 187: sampling and conditioning

For paper tensile testing on the same frame, see our ISO 1924-2 guide. Browse all methods on our ISO standards page.

ISO 3035 Equipment from Universal Grip

Universal Grip's ISO 3035 Compression Platens (part ref. UGC-ISO3035-CP) are a guided compression platen set for crush testing of corrugated fibreboard. The upper platen rides on four precision posts in ball bushings, so it stays parallel to the lower platen through the stroke. That four-post guidance addresses the lateral-movement problem that causes leaning flutes on unguided platens.

  • Test method: ISO 3035 crush resistance

  • Loading: compression between guided parallel platens

  • Specimens: circular single-wall corrugated board test pieces per ISO 3035

  • Load capacity: 5 kN typical; higher capacities on request

  • Material: corrosion-protected steel platens, hardened guide posts

  • Contact surfaces: flat, ground parallel platens sized for flat crush and edge crush specimens

  • Guidance: four guide posts in recirculating ball bushings

  • Machine connection: central threaded spigot to the load cell; supplied with adapters (clevis or threaded) to suit your load frame

Note: The platen set is a combined crush fixture. It includes a pair of guide blocks that hold edge crush (ECT, ISO 3037) specimens upright and square to the platens. The guide blocks are not used for flat crush: for ISO 3035, the circular test piece sits flat and centered on the open lower platen with nothing touching its edge. The same fixture then covers both FCT and ECT on one machine.

When you request a quote, tell us which crush tests you run (flat crush, edge crush), your test piece size, the force range and your test machine connection. The platens fit our universal testing machines and most electromechanical frames through the supplied adapters. Pair them with test software that captures the full force-deflection curve so you can report the first collapse peak and review leaning-flute behavior. See our compression testing applications and wider range of compression fixtures, or contact us for a quote.

ISO 3035 FAQ

What is the current edition of ISO 3035?

The current edition is ISO 3035:2025, the fourth edition, published in July 2025. It replaced ISO 3035:2011 and was adopted in Europe as EN ISO 3035:2025. The main changes were removal of the beam-deflection tester note, a new Precision clause and updated Cepi-CTS precision data.

What does the flat crush test (FCT) tell you about corrugated board?

FCT measures how much pressure the flutes withstand, applied perpendicular to the board surface, before they collapse. It shows flute rigidity and, above all, whether the flutes were damaged on the corrugator or in printing, die-cutting and handling. It is a quality-control indicator rather than a direct predictor of box stacking strength.

What size test piece does ISO 3035 use?

ISO 3035 uses circular test pieces cut with a guided circular knife. The usual sizes are 100 cm² (112.8 mm diameter) and 50 cm² (79.8 mm diameter). Record the actual area and use it in the calculation.

What test speed is used for ISO 3035?

The platens close at 12.5 mm/min ± 2.5 mm/min on a motor-driven, fixed-platen tester. TAPPI T 825 uses the same nominal speed with a much tighter ±0.25 mm/min tolerance, so a well-controlled machine set to 12.5 mm/min satisfies both.

How do you calculate flat crush resistance?

Divide the maximum force before flute collapse by the test piece area: FCT = Fmax / A. For example, 2,410 N on a 100 cm² (0.0100 m²) piece gives 241,000 Pa, or 241 kPa. A quick check is N per cm² multiplied by 10 equals kPa.

How many test pieces are needed for ISO 3035?

Plan on at least 10 valid test pieces per sample, which is the customary minimum for ISO 3035 work and matches the FEFCO and TAPPI flat crush methods. Cut spares so you can replace pieces with damaged edges or leaning flutes, and always report how many you tested.

Can ISO 3035 be used for double-wall or microflute board?

No. The 2025 scope covers single-faced and single-wall board only. Double-wall and microflute board are excluded because the end-point of the test is not clearly defined or observable, so any number produced would not be a valid ISO 3035 result.

Is there an ASTM equivalent to ISO 3035?

There is no ASTM flat crush method for corrugated board. The North American counterpart is TAPPI T 825 (rigid support method), which uses the same principle and nominal speed but different specimen areas and a tighter speed tolerance. TAPPI T 808 is a separate flexible-beam method whose results are not comparable.

Why do flutes lean instead of crushing straight down?

Leaning or rolling flutes usually come from lateral movement of the moving platen, an off-center test piece, or poorly formed flutes in the board. Guided platens and careful centering reduce the machine-related causes. Note any leaning-flute pieces in the report because they give low values.

Can I run ISO 3035 on a universal testing machine?

Yes, provided the machine meets ISO 13820 for speed and force measurement and is fitted with rigid, flat, parallel platens with minimal lateral movement. A 5 kN-class benchtop universal testing machine with guided compression platens covers most single-wall board.

What conditioning does ISO 3035 require?

Test pieces are conditioned and tested in the ISO 187 standard atmosphere of 23 °C ± 1 °C and 50 % ± 2 % relative humidity, with preconditioning on the dry side. Corrugated board is very sensitive to moisture, so testing unconditioned board can swamp the differences you want to measure.

Do I need the guide blocks on a combined crush fixture for flat crush?

No. Guide blocks support edge crush (ISO 3037) specimens standing on edge. For ISO 3035 flat crush, remove or set aside the guide blocks and place the circular test piece flat and centered on the lower platen. Contact us if you want one fixture for both tests.

Need a fixture, grips or a complete test system for ISO 3035? Contact Universal Grip with your material, specimen size and machine connection and we will quote the right setup.

bottom of page