Home › Products › Cutting Dies › GOST 22372 Cutting Die
GOST 22372 Cutting Die – Dielectric Disc
Dielectric disc · Permittivity / dielectric loss specimen — built to GOST 22372. Hardened steel or economical ribbon steel.
Brand: Universal Grip | Model: UGC-CDH-GOST22372 / UGC-CDR-GOST22372 | ● Made to order
Cuts the GOST 22372 dielectric Disc profile: diameter 50 mm, allowed diameter range 25 to 150 mm
Two styles: hardened steel for 0–5 mm, ribbon steel for 0–3 mm
Integral ejector (hardened) or foam pad (ribbon) pushes each specimen free
Fits manual, pneumatic and hydraulic sample-cutting presses
Free test cuts on your material before you order
Custom profiles, multi-cavity dies and nick/notch features on request
Downloads: Ribbon Steel Die Data Sheet (PDF)
Standards: GOST 22372
Trusted by Global Companies
Precision cutting die for GOST 22372 dielectric Disc specimens
This Universal Grip die cuts the dielectric disc (permittivity / dielectric loss specimen) defined in GOST 22372: Dielectric materials - Methods for determination of permittivity and dielectric loss tangent at 100 Hz to 5 MHz. Flat disc specimens are placed between electrodes to measure permittivity and loss tangent from 100 Hz to 5 MHz. Specimen diameter is chosen to suit the electrode set, with 50 mm a common size.
We make it in two styles so the die suits the material you cut. The one-piece hardened steel die is machined from a single piece of steel and holds its edge on rigid & semi-rigid plastics, filled compounds, rubber, sheet & film from 0 to 5 mm thick. The ribbon steel (steel-rule) die uses a precision-bent hardened rule in a laser-cut plywood base with a foam ejection pad, an economical choice for rubber, elastomers, TPE, foams, soft plastics & films up to 3 mm. Both cut the same GOST 22372 profile.
GOST 22372 specimen dimensions
The die is cut to the nominal profile in GOST 22372: diameter 50 mm, allowed diameter range 25 to 150 mm, diameter-to-thickness ratio (min) 10:1 and minimum film thickness 0.15 mm. Always check your current edition of the standard for tolerances and the test procedure.
Where it is used
Typical uses for GOST 22372 specimens include insulating films and sheet, PCB laminates, cable insulation compounds and elastomeric insulators.
Cutting specimens with the die
Put the die on an arbor press or a pneumatic press, set your sheet on a nylon cutting plate and press through in one stroke; the ejector pushes the specimen out ready to test. No press yet? An adapter lets the die run on your universal testing machine. Send us a sample of your material and we will make test cuts free of charge, so you can confirm the edge quality before you order. Hardened dies can be re-sharpened with our die sharpening tool.
GOST 22372 Cutting Die Specifications
STANDARD
GOST 22372
SPECIMEN
Dielectric disc
SPECIMEN TYPE
Permittivity / dielectric loss specimen
DIAMETER
50 mm
ALLOWED DIAMETER RANGE
25 to 150 mm
DIAMETER-TO-THICKNESS RATIO (MIN)
10:1
MINIMUM FILM THICKNESS
0.15 mm
HARDENED STEEL DIE
One-piece machined steel, 0–5 mm material, integral ejector plate
RIBBON STEEL DIE
Steel rule in plywood base, 0–3 mm material, foam ejection pad
PRESS COMPATIBILITY
Manual, pneumatic & hydraulic sample-cutting presses
PART NUMBERS
UGC-CDH-GOST22372 (hardened) · UGC-CDR-GOST22372 (ribbon)
Models & Options
Hardened Steel Cutting Die — One-piece machined, hardened and precision-finished; rigid & semi-rigid plastics, filled compounds, rubber, sheet & film; 0–5 mm; integral ejector plate; re-sharpenable (UGC-CDH-GOST22372)
Ribbon Steel Cutting Die — Precision-bent hardened steel rule in a laser-cut plywood base with closed-cell foam ejection pad; rubber, elastomers, TPE, foams, soft plastics & films; 0–3 mm; economical, fast turnaround (UGC-CDR-GOST22372)
Press mounting — Matched to your press make and model, or an adapter for your universal testing machine (Specify at order)
Custom features — Custom profiles, multi-cavity dies and nick/notch features on request (Custom)
What's Included
GOST 22372 cutting die in your chosen style (hardened or ribbon steel)
Specimen ejection: integral ejector plate (hardened) or foam ejection pad (ribbon)
Mounting to suit your press — tell us the make and model
Data sheet with the nominal profile dimensions
Supported Test Standards
GOST 22372 — Dielectric materials - Methods for determination of permittivity and dielectric loss tangent at 100 Hz to 5 MHz
Compatible Grips & Fixtures
Arbor press — Benchtop press for cutting dielectric Disc specimens with this die
Sample die press — Specimen-preparation presses and tools
Die sharpening tool — Restore the cutting edge of a hardened steel die
Plastics testing — Grips and fixtures for plastic film, sheet and molded parts
“Customer quote”
Related Equipment
GOST 13518 Cutting Die
Bent-strip ESCR Specimen · length 38 mm, width 13 mm
GOST 15088 Cutting Die
Vicat Square · length (min) 10 mm, width (min) 10 mm
GOST 4651 Cutting Die
Compression Prism (Type A) · length 50 ± 2 mm, width 10.0 ± 0.2 mm
GOST 6433.3 Cutting Die
Breakdown Disc · diameter 100 mm, allowed diameter range 25 to 150 mm
GOST 22372 Cutting Die FAQ
What is the GOST 22372 test used for?
Flat disc specimens are placed between electrodes to measure permittivity and loss tangent from 100 Hz to 5 MHz. Specimen diameter is chosen to suit the electrode set, with 50 mm a common size.
What are the GOST 22372 specimen dimensions?
The die cuts the nominal GOST 22372 profile: diameter 50 mm, allowed diameter range 25 to 150 mm, diameter-to-thickness ratio (min) 10:1 and minimum film thickness 0.15 mm. These values come from the standard; check your current edition for tolerances.
Hardened steel or ribbon steel: which GOST 22372 die should I choose?
For rigid and semi-rigid plastics, filled compounds and sheet up to 5 mm, choose the hardened steel die. The ribbon steel die is the economical option for soft plastics and films up to 3 mm.
Which press do I need for the GOST 22372 die?
The die fits manual, pneumatic and hydraulic sample-cutting presses. On our arbor press it mounts with a lateral screw, and an adapter lets it run on a universal testing machine. Tell us your press make and model and we will match the mounting.
Can you make test cuts on my material?
Yes. Send us a sample of your sheet and we will make test cuts free of charge, so you can see the edge quality and confirm the right die style before you order.
Can you make a custom or multi-cavity GOST 22372 die?
Yes. We make custom profiles, multi-cavity dies and nick or notch features on request. Send the drawing or standard, your material and thickness, and your press model.