Home › Products › Cutting Dies › JIS K7162 1B Cutting Die
JIS K7162 1B Cutting Die – Tensile Dumbbell
Tensile Dumbbell Type 1B · Tensile specimen — built to JIS K7162. Hardened steel or economical ribbon steel.
Brand: Universal Grip | Model: UGC-CDH-JISK7162-T1B / UGC-CDR-JISK7162-T1B | ● Made to order
Cuts the JIS K7162 1B tensile Dumbbell profile: 10.0 × 60.0 mm narrow section, 150 mm overall length
Two styles: hardened steel for 0–5 mm, ribbon steel for 0–3 mm
Integral ejector (hardened) or foam pad (ribbon) pushes each specimen free
Fits manual, pneumatic and hydraulic sample-cutting presses
Free test cuts on your material before you order
Custom profiles, multi-cavity dies and nick/notch features on request
Downloads: Ribbon Steel Die Data Sheet (PDF)
Standards: JIS K7162 · ISO 527-2
Trusted by Global Companies
Precision cutting die for JIS K7162 1B tensile Dumbbell specimens
This Universal Grip die cuts the tensile Dumbbell Type 1B (tensile specimen) defined in JIS K7162: Testing method for tensile properties of plastics (moulding and extrusion plastics). JIS K7162 was the earlier Japanese adoption of ISO 527-2 for molding and extrusion plastics. Type 1B is the machined or die-cut alternative with a larger shoulder radius.
We make it in two styles so the die suits the material you cut. The one-piece hardened steel die is machined from a single piece of steel and holds its edge on rigid & semi-rigid plastics, filled compounds, rubber, sheet & film from 0 to 5 mm thick. The ribbon steel (steel-rule) die uses a precision-bent hardened rule in a laser-cut plywood base with a foam ejection pad, an economical choice for rubber, elastomers, TPE, foams, soft plastics & films up to 3 mm. Both cut the same JIS K7162 1B profile.
JIS K7162 1B specimen dimensions
The die is cut to the nominal profile in JIS K7162: overall length (min) 150 mm, width of ends 20.0 ± 0.2 mm, width of narrow section 10.0 ± 0.2 mm, length of narrow section 60.0 ± 0.5 mm, transition radius (min) 60 mm, gauge length 50.0 ± 0.5 mm and recommended thickness 4.0 ± 0.2 mm. Always check your current edition of the standard for tolerances and the test procedure.
1B compared with other JIS K7162 dies
1B: 10.0 × 60.0 mm narrow section, 150 mm overall length (this die)
Where it is used
Typical uses for JIS K7162 1B specimens include molded plastic resin QC, material datasheet property generation, incoming resin lot acceptance and polymer R&D and compound comparison.
Cutting specimens with the die
Put the die on an arbor press or a pneumatic press, set your sheet on a nylon cutting plate and press through in one stroke; the ejector pushes the specimen out ready to test. No press yet? An adapter lets the die run on your universal testing machine. Send us a sample of your material and we will make test cuts free of charge, so you can confirm the edge quality before you order. Hardened dies can be re-sharpened with our die sharpening tool.
JIS K7162 1B Cutting Die Specifications
STANDARD
JIS K7162 1B
SPECIMEN
Tensile Dumbbell Type 1B
SPECIMEN TYPE
Tensile specimen
OVERALL LENGTH (MIN)
150 mm
WIDTH OF ENDS
20.0 ± 0.2 mm
WIDTH OF NARROW SECTION
10.0 ± 0.2 mm
LENGTH OF NARROW SECTION
60.0 ± 0.5 mm
TRANSITION RADIUS (MIN)
60 mm
GAUGE LENGTH
50.0 ± 0.5 mm
RECOMMENDED THICKNESS
4.0 ± 0.2 mm
HARDENED STEEL DIE
One-piece machined steel, 0–5 mm material, integral ejector plate
RIBBON STEEL DIE
Steel rule in plywood base, 0–3 mm material, foam ejection pad
PRESS COMPATIBILITY
Manual, pneumatic & hydraulic sample-cutting presses
PART NUMBERS
UGC-CDH-JISK7162-T1B (hardened) · UGC-CDR-JISK7162-T1B (ribbon)
Models & Options
Hardened Steel Cutting Die — One-piece machined, hardened and precision-finished; rigid & semi-rigid plastics, filled compounds, rubber, sheet & film; 0–5 mm; integral ejector plate; re-sharpenable (UGC-CDH-JISK7162-T1B)
Ribbon Steel Cutting Die — Precision-bent hardened steel rule in a laser-cut plywood base with closed-cell foam ejection pad; rubber, elastomers, TPE, foams, soft plastics & films; 0–3 mm; economical, fast turnaround (UGC-CDR-JISK7162-T1B)
Press mounting — Matched to your press make and model, or an adapter for your universal testing machine (Specify at order)
Custom features — Custom profiles, multi-cavity dies and nick/notch features on request (Custom)
What's Included
JIS K7162 1B cutting die in your chosen style (hardened or ribbon steel)
Specimen ejection: integral ejector plate (hardened) or foam ejection pad (ribbon)
Mounting to suit your press — tell us the make and model
Data sheet with the nominal profile dimensions
Supported Test Standards
JIS K7162 — Testing method for tensile properties of plastics (moulding and extrusion plastics)
ISO 527-2 — Related standard: tensile properties of moulding and extrusion plastics
Compatible Grips & Fixtures
Arbor press — Benchtop press for cutting tensile Dumbbell specimens with this die
Sample die press — Specimen-preparation presses and tools
Wedge grips — Self-tightening wedge grips for rigid plastic dumbbells
Pneumatic grips — Constant clamping force for thin or soft plastics
Die sharpening tool — Restore the cutting edge of a hardened steel die
Marking tool — Repeatable 50.0 mm gauge marks for video extensometers
Plastics testing — Grips and fixtures for plastic film, sheet and molded parts
“Customer quote”
Related Equipment
JIS K7162 1A Cutting Die
Tensile Dumbbell · 10.0 × 80 mm narrow section
GOST 11262 Fig. 1 Type 1B Cutting Die
Machined Dumbbell · 10.0 × 60.0 mm narrow section
ISO 20753-A2 Cutting Die
Multipurpose Dumbbell Type A2 · 10.0 × 60.0 mm narrow section
ISO 3167 Type B Cutting Die
Multipurpose Dumbbell · 10.0 × 60.0 mm narrow section
JIS K7162 1B Cutting Die FAQ
What is the JIS K7162 test used for?
JIS K7162 was the earlier Japanese adoption of ISO 527-2 for molding and extrusion plastics. Type 1B is the machined or die-cut alternative with a larger shoulder radius.
What are the JIS K7162 1B specimen dimensions?
The die cuts the nominal JIS K7162 profile: overall length (min) 150 mm, width of ends 20.0 ± 0.2 mm, width of narrow section 10.0 ± 0.2 mm, length of narrow section 60.0 ± 0.5 mm, transition radius (min) 60 mm, gauge length 50.0 ± 0.5 mm and recommended thickness 4.0 ± 0.2 mm. These values come from the standard; check your current edition for tolerances.
Hardened steel or ribbon steel: which JIS K7162 1B die should I choose?
For rigid and semi-rigid plastics, filled compounds and sheet up to 5 mm, choose the hardened steel die. The ribbon steel die is the economical option for soft plastics and films up to 3 mm.
Which press do I need for the JIS K7162 1B die?
The die fits manual, pneumatic and hydraulic sample-cutting presses. On our arbor press it mounts with a lateral screw, and an adapter lets it run on a universal testing machine. Tell us your press make and model and we will match the mounting.
How do I grip and measure JIS K7162 1B specimens?
Hold the wide ends in wedge grips or pneumatic grips so the specimen is loaded straight along its axis. The gauge length is 50.0 ± 0.5 mm; our marking tool applies repeatable gauge marks for video extensometers.
Which other JIS K7162 dies do you make?
We also make cutting dies for 1A, each in hardened and ribbon steel.
Can you make test cuts on my material?
Yes. Send us a sample of your sheet and we will make test cuts free of charge, so you can see the edge quality and confirm the right die style before you order.
Can you make a custom or multi-cavity JIS K7162 1B die?
Yes. We make custom profiles, multi-cavity dies and nick or notch features on request. Send the drawing or standard, your material and thickness, and your press model.