top of page

Home  ›  Products  ›  Compression Platens  ›  Pull Cage for Compression 140 x 200 mm

UGC-CC-010 four-column pull cage for compression with 140 x 200 mm platens by Universal Grip
UGC-CC-010 four-column pull cage for compression with 140 x 200 mm platens by Universal Grip
UGC-CC-010 Pull Cage for Compression 140 x 200 mm by Universal Grip, view 2
UGC-CC-010 Pull Cage for Compression 140 x 200 mm by Universal Grip, view 3
UGC-CC-010 Pull Cage for Compression 140 x 200 mm by Universal Grip, view 4

Pull Cage for Compression 140 x 200 mm

Four-column pull cage with 140 x 200 mm platens and 220 mm working space that turns machine tension into specimen compression, rated -70 to +280 °C.

Brand: Universal Grip  |  Model: UGC-CC-010  |  ● Configured to order

  • Converts the machine's tensile stroke into compression on the specimen

  • Large 140 x 200 mm (5.5 x 7.9 in) platens for bulky specimens

  • 220 mm (8.7 in) working space between the platens

  • Four guide rods keep the platens parallel as they travel

  • Rated -70 to +280 °C (-94 to +536 °F) for use inside a temperature chamber

  • Nickel-plated steel construction; male clevis with Ø 35 mm pin hole

Downloads and standards

Trusted by Global Companies

Four-column pull cage for compression tests in temperature chambers

The UGC-CC-010 is a pull cage for laboratories that need to run compression tests on a machine set up to pull, most often because the specimen sits inside a temperature chamber on pull rods. Two interlocking frames, each carrying one 140 x 200 mm (5.5 x 7.9 in) platen, slide on four guide rods. When the machine pulls the frames apart, the platens inside close on the specimen and compress it. The cage gives 220 mm (8.7 in) of working space between the platens, enough for foam blocks, molded parts, springs and other bulky specimens.

 

How it works

The upper frame hangs from the machine's upper coupling with its platen at the bottom; the lower frame is attached to the lower coupling with its platen at the top. Because the two frames interlock, pulling them apart drives the platens together. The load train outside the cage stays in tension, so long pull rods through a chamber wall carry the force without the buckling risk of long push rods. Four guide rods keep the platens parallel through the stroke, so the specimen is compressed evenly across its face.

The cage is nickel-plated steel for corrosion resistance and is rated for -70 to +280 °C (-94 to +536 °F), covering cold, ambient and elevated-temperature tests in the same setup.

 

Coupling and configuration

The machine connection is a male clevis with a Ø 35 mm (1.38 in) pin hole, and adapters fit it to other couplings. Maximum load is confirmed on request, so tell us the load your test needs. Platen size, working space, coupling and temperature range can be specified to order where the standard cage doesn't fit your specimen or chamber.

 

Typical applications

  • Foams and elastomers at temperature

  • Plastic and composite parts

  • Springs and components

  • Compression set studies

 

Choosing a compression cage

For lighter loads where low friction matters, the UGC-CC-020 ball bearing compression cage is rated to 10 kN with 100 x 100 mm platens and 250 mm of travel. For a compact heavy-duty unit with a ceramic loading insert, see the UGC-CC-030. The UGC-CC-010 is the choice when you need large platens and a wide temperature range in one cage. It runs on a Galdabini universal testing machine with an environmental chamber; see compression platens for push-type alternatives.

Tell us the required load, platen size, working space, coupling and temperature range, and we'll configure the cage: request a quote.

Product video

At a glance

  • Test type: Compression via tension (pull cage)

  • Construction: Two interlocking frames

  • Platen size: 140 x 200 mm

  • Working space: 220 mm between platens

  • Guides: Four guide rods

  • Coupling: Male clevis, Ø 35 mm pin hole

Pull Cage for Compression 140 x 200 mm Specifications

TEST TYPE

Compression via tension (pull cage)

 

CONSTRUCTION

Two interlocking frames

 

PLATEN SIZE

140 x 200 mm

 

WORKING SPACE

220 mm between platens

 

GUIDES

Four guide rods

 

COUPLING

Male clevis, Ø 35 mm pin hole

 

MATERIAL

Steel, nickel-plated

 

TEMPERATURE RANGE

-70 to +280 °C

 

MAX. LOAD

On request

 

DRAWINGS

Dimensional drawings and 3D models on request

 

PART REF.

UGC-CC-010

 

Models & Options

  • Platen size — 140 x 200 mm standard; other sizes to order (On request)

  • Working space — 220 mm standard; other heights to order (On request)

  • Machine coupling — Male clevis, Ø 35 mm pin hole; adapters for other couplings (Specify at order)

  • Load rating — Confirmed to your test load (On request)

What's Included

  • Pull cage: two interlocking frames with 140 x 200 mm platens on four guide rods

  • Male clevis coupling with Ø 35 mm pin hole

  • Exact scope of supply confirmed with your quote

Supported Test Standards

Standards list

Compatible Grips & Fixtures

“Customer quote”

Related Equipment

UGC-CC-020 Ball Bearing Compression Cage 10 kN

UGC-CC-020 Ball Bearing Compression Cage 10 kN

Ball-bearing guided cage rated to 10 kN for compression and tension tests, with 100 x 100 mm anodized aluminum platens a

UGC-CC-030 Compression Cage with Ceramic Insert

UGC-CC-030 Compression Cage with Ceramic Insert

Compact Ø 96 mm heavy-duty pull cage that redirects machine tension into specimen compression, with a ceramic insert at

Related product 3

Related 3

Related product 4

Related 4

Pull Cage for Compression 140 x 200 mm FAQ

What is a pull cage for compression?

A fixture that turns the machine's tensile stroke into compression. Pulling the two interlocking frames apart drives the platens together on the specimen.

 

How big are the platens and working space?

140 x 200 mm platens with 220 mm of working space between them.

 

Can it be used in a temperature chamber?

Yes. The cage is rated for -70 to +280 °C and is meant to run inside an environmental chamber on pull rods.

 

What is the maximum load?

Maximum load is confirmed on request. Tell us the load your test needs.

 

What coupling does it use?

A male clevis with a Ø 35 mm pin hole. Adapters are available for other couplings.

 

Can the cage be built to other dimensions?

Yes. Platen size, working space, coupling and temperature range can be specified to order.

 

Need help configuring a compression platen?

Tell us your material, test standard and specimen size. We will recommend the frame, force sensor, grips and fixtures, and send a quote.

bottom of page