ISO 3167
Multipurpose Test Specimens for Plastics

Downloads: ISO 3167 Multipurpose Dumbbell Specimen Cutter for Plastics – Universal Grip Data Sheet (PDF)
Written by Chris Thomas, Universal Grip Company · Reviewed by Frank Bertini · Updated October 31, 2026
ISO 3167 defines the multipurpose test specimen for plastics. This is the familiar 10 × 4 mm dumbbell that most ISO plastics data is built on. The specimen can be tested whole in tension, or its parallel centre section can be cut into an 80 × 10 × 4 mm bar for flexural, impact, heat deflection and other tests. Resin makers, compounders, molders and test labs use it so that every property on a data sheet comes from the same geometry and the same molding history.
ISO 3167 is a specimen standard, not a test method. It tells you what the specimen looks like and how it may be made. The test methods themselves (ISO 527-2, ISO 178, ISO 179 and so on) tell you how to test it. Labs often get it wrong by treating any dumbbell of roughly the right size as "multipurpose", or by ignoring the fact that how the specimen was made changes the results. This guide covers the Type A and Type B geometries, injection molding, compression molding, machining and die cutting (including when die cutting is and is not appropriate), conditioning, the downstream tests, a worked tensile calculation, common errors and how ISO 3167 compares with ASTM D638.
ISO 3167 at a glance
-
Current edition: ISO 3167:2014 (fifth edition), confirmed by ISO in 2026. It reinstated the 2002 edition after that was withdrawn in 2013. ISO intends ISO 3167 to be gradually replaced by ISO 20753.
-
Scope: Multipurpose test specimens for plastic moulding materials that are processed by injection or direct compression moulding.
-
Specimens: Type A and Type B dumbbells, both 10 mm wide and 4 mm thick in the narrow section with 20 mm wide ends. They differ in shoulder geometry and parallel length.
-
Tensile equivalents: Type A is the shape of the ISO 527-2 Type 1A specimen and Type B the shape of Type 1B.
-
Preparation: Injection moulding, compression moulding or machining, covered in Clause 4. Die cutting is a sheet-preparation shortcut that suits thinner or softer materials only (see below).
-
Uses: Tensile tests directly, plus bars cut from the centre section for flexural, impact, heat deflection and other tests (Annex A lists recommended applications).
-
Conditioning: Not set by ISO 3167. It comes from the test method and material standard, usually ISO 291 at 23 °C / 50 % RH.
-
Related standards: ISO 527-1, ISO 527-2, ISO 178, ISO 179-1, ISO 180, ISO 75-2, ISO 604, ISO 294-1, ISO 293, ISO 2818, ISO 20753, ISO 10350-1.
Why a multipurpose specimen?
Plastics properties depend strongly on how the specimen was made. Melt temperature, mould temperature, injection speed and flow direction set molecular orientation, crystallinity, residual stress and, for filled grades, fibre orientation. If the tensile bar, flex bar and impact bar each came from a different mould, you would be comparing three different materials. One multipurpose specimen, moulded under recorded conditions, gives the tensile test and the bars cut from its centre section the same internal state.
This is the basis of comparable single-point and multipoint data under ISO 10350-1 and ISO 11403 and of databases built on them. It is why the ISO 527-2 Type 1A specimen is described as the preferred specimen for thermoplastic moulding materials. Typical users include:
-
Resin producers and compounders generating data sheet values
-
Injection molders qualifying incoming resin lots or regrind ratios
-
Independent and accredited plastics test labs
-
Automotive, appliance and electrical OEMs approving materials to their specifications
-
Universities and R&D teams comparing formulations
Specimen dimensions: Type A and Type B
Both types share the same cross-section and end width. The common, well-established dimensions are listed below. Take shoulder tolerances and the distance between the broad ends from your copy of the standard, because they differ between Type A and Type B.
Type A (ISO 527-2 Type 1A shape)
-
Overall length: 170 mm (recommended for moulded specimens)
-
Narrow parallel section: 80 ± 2 mm long
-
Width of narrow section: 10.0 ± 0.2 mm
-
Width of ends: 20.0 ± 0.2 mm
-
Thickness: 4.0 ± 0.2 mm
-
Shoulder radius: about 20 to 25 mm (the short, tight shoulder suits a mould and gives an 80 mm bar)
-
When tested to ISO 527-2: gauge length 75 mm preferred (50 mm is also used for quality control), initial grip separation about 115 mm
Type B (ISO 527-2 Type 1B shape)
-
Overall length: 150 mm minimum
-
Narrow parallel section: 60 mm long
-
Width of narrow section 10 mm, width of ends 20 mm, thickness 4 mm
-
Shoulder radius: 60 mm (a long, gentle transition that suits machining from sheet)
-
When tested to ISO 527-2: gauge length 50 mm, initial grip separation about 115 mm
In general, Type A is used for directly moulded specimens and Type B for machined specimens. Annex B of ISO 3167 explains what changes in geometry do to results. For example, the shorter parallel length of Type B cannot provide a full 80 mm bar for flexural testing.
How multipurpose specimens are made
Be clear about this before buying any equipment. Multipurpose specimens are normally injection moulded, or machined from compression-moulded plaques. ISO 3167 Clause 4 covers three routes:
-
Injection moulding (Clause 4.2): The reference route for thermoplastics. The mould and process follow ISO 294-1, whose Type A1 cavity produces the multipurpose specimen, using conditions from the material standard. Thermosets follow ISO 10724-1.
-
Compression moulding (Clause 4.3): For materials that cannot be injection moulded, or where a plaque is needed. Thermoplastics follow ISO 293 and thermosets ISO 295.
-
Machining (Clause 4.4): Milling the profile from a moulded plaque or sheet according to ISO 2818. This route gives Type B naturally, and it is the right route for rigid, brittle, filled or glass-reinforced materials.
Die cutting with a specimen cutter is an additional practical route, not one of the moulding routes. It suits thinner and softer sheet, such as unfilled PE, PP, TPO, plasticised PVC and other ductile materials at the low end of the 4 mm thickness or below. A hardened die pressed through a 4 mm rigid or glass-filled sheet can crack, crush or leave concave, non-parallel edges. That spoils tensile and especially impact results, so machine those materials instead. Die-cut specimens from extruded sheet also carry the sheet's own orientation, not that of a moulded specimen. Report them as cut from sheet, and do not present them as moulded multipurpose data.
The Universal Grip ISO 3167 specimen cutter
Our ISO 3167 Specimen Cutter (part ref. UGC-ISO3167-SC) is a precision cutting die for producing multipurpose dumbbell specimens from plastic sheet. The die's hardened, sharpened edge follows the standard Type A outline (ISO 527-2 Type 1A). A spring-loaded ejector plate pushes the cut specimen out cleanly, which gives consistent gauge width and shoulder radii from specimen to specimen.
-
Cutting edge follows the multipurpose Type A dumbbell outline
-
Hardened, precision-ground steel cutting edge for clean, burr-free specimen sides
-
Spring-loaded, screwed ejector plate releases specimens without distortion
-
Steel die on a heavy, solid backing block for rigid, even support under press load
-
Suits manual hand-lever, toggle or pneumatic specimen presses
-
Material thickness range: thin to moderate sheet. Confirm the material and thickness at quote.
-
Type B and custom dumbbells available on request
To be clear about where it fits: this cutter is for labs that need ISO 527-2 Type 1A-shaped tensile specimens from sheet, for example extruded-sheet QC, unfilled thermoplastic sheet and quick screening work. It does not replace an injection mould for generating multipurpose data, and it is not the right tool for thick, rigid or reinforced grades. When ordering, tell us the specimen type, the material and thickness range, and the press you will use. We offer free test cuts on your material, which is the quickest way to find out whether die cutting gives acceptable edges. See our cutting dies and arbor presses (8, 17 and 26 kN manual, 100 kN air-hydraulic), or the die press range.
Conditioning
ISO 3167 does not set conditioning itself. The test method and material standard do, and most require conditioning in a standard atmosphere to ISO 291, typically 23 °C and 50 % relative humidity, for a minimum time before testing. Moisture-sensitive materials such as polyamides need special treatment. Their material standards specify testing dry-as-moulded or after conditioning (ISO 1110 describes accelerated conditioning). Machined and die-cut specimens should also be conditioned after preparation, because cutting can warm the edges. Record moulding conditions and specimen preparation as Clause 5 of ISO 3167 requires.
What the multipurpose specimen is used for
Annex A of ISO 3167 lists recommended applications. The most common are:
-
Tensile properties to ISO 527-2 (general principles in ISO 527-1): the whole specimen, with the modulus measured at 1 mm/min and strength usually at 5 or 50 mm/min depending on whether the material is brittle or ductile
-
Flexural properties to ISO 178: the 80 × 10 × 4 mm bar cut from the Type A parallel section, tested at a 64 mm span
-
Charpy impact to ISO 179-1 and Izod impact to ISO 180: the 80 × 10 × 4 mm bar, notched or unnotched
-
Heat deflection temperature to ISO 75-2: the 80 × 10 × 4 mm bar, typically flatwise
-
Compressive properties to ISO 604: prisms cut from the centre section (check ISO 604 for the preferred lengths for modulus and strength)
-
Vicat softening temperature (ISO 306), hardness and other small-piece tests on sections of the specimen
This is why Type A is preferred for moulding. Its 80 mm parallel section yields a full-length bar. Type B's 60 mm parallel section is too short for an 80 mm bar.
Testing the multipurpose specimen: machines and accessories
Forces involved
The 10 × 4 mm section is 40 mm², so the tensile force is simply strength × 40. Unfilled PE and PP break or yield at roughly 1 to 1.5 kN. Engineering thermoplastics such as PC, PA and POM reach about 2 to 3 kN, and 30 % glass-filled polyamides and similar grades can approach 7 kN. Flexural and compression tests on the cut bars need well under 1 kN in most cases.
Mark-10 or Galdabini?
A Mark-10 F-series motorized tester such as the F1505 (6.7 kN) can handle QC tensile strength and elongation on unfilled and moderately filled grades at 50 mm/min. Be realistic, though. ISO 527 modulus has to be measured at 1 mm/min with a suitable extensometer, and the F755 and F1505 run 10 to 600 mm/min. The low-speed option (to 0.5 mm/min) is offered on the F105 to F505, which top out at 2.2 kN and have too little force for stronger grades. For full ISO 527-2 data, including modulus, use a Galdabini universal testing machine. A 5 kN or 10 kN benchtop frame covers most unfilled plastics, and a 25 kN frame gives headroom for glass-filled grades and elevated-temperature work with an environmental chamber (−80 to +280 °C).
Grips and extensometers
Wedge-action or pneumatic grips with serrated faces wide enough for the 20 mm ends hold the specimen without slip. See our wedge grips, pneumatic grips and tensile grips. Modulus needs an extensometer on the gauge length: a clip-on extensometer removed before break, or a video extensometer that follows the specimen through break. For flexural tests on the cut bars, use our bend testing fixtures.
Step-by-step: preparing and testing ISO 3167 specimens
-
1. Choose the route. Injection moulding to ISO 294-1 for reference data, compression moulding plus machining for non-mouldable materials, or die cutting from sheet only for thinner or softer ductile materials.
-
2. Prepare the specimens. Mould with recorded conditions, or machine to ISO 2818, or die-cut in one steady press stroke with a sharp die on a flat, rigid backing.
-
3. Inspect for sink marks, voids, flash, warp, burrs and tapered edges. Discard any defective specimens.
-
4. Measure the width and thickness of the narrow section and record them.
-
5. Condition to ISO 291 or the material standard.
-
6. Test in tension to ISO 527-2. Set the grip separation, attach the extensometer, run the modulus phase at 1 mm/min, then continue at the strength speed.
-
7. Cut bars from the centre section of other specimens for flexural, impact or HDT testing, following each method's instructions.
-
8. Report the specimen type, preparation route and conditions along with the results.
Worked example: tensile strength and modulus
A Type A specimen is die-cut from 4 mm unfilled PP sheet and tested to ISO 527-2 with a 75 mm gauge length.
-
Measured width 10.05 mm, thickness 3.98 mm, so A = 10.05 × 3.98 = 40.0 mm²
-
Maximum force 1,320 N, so tensile strength σm = 1,320 / 40.0 = 33.0 MPa
-
Modulus (chord between strains of 0.05 % and 0.25 %): on a 75 mm gauge length these strains are extensions of 0.0375 mm and 0.1875 mm
-
Forces at those points are 32 N and 168 N, so the stresses are 0.80 MPa and 4.20 MPa
-
Et = (4.20 − 0.80) / (0.0025 − 0.0005) = 3.40 / 0.0020 = 1,700 MPa
The modulus extensions are in the hundredths of a millimetre, which is why a proper extensometer is needed. Crosshead displacement includes machine and grip compliance and cannot give a valid ISO 527 modulus.
What to report
-
A reference to ISO 3167 and the specimen type (A or B)
-
The preparation route: injection moulded (ISO 294-1, with conditions), compression moulded (ISO 293 or ISO 295), machined (ISO 2818) or die-cut from sheet
-
Material identification, including lot, colour, filler and any drying
-
Measured dimensions and any specimens rejected
-
Conditioning and test atmosphere
-
The test method used for each property (ISO 527-2, ISO 178, ISO 179-1, etc.) and its results
Common errors
-
Calling a die-cut sheet specimen "multipurpose moulded data". Its orientation and edge condition differ, so state how it was made.
-
Die-cutting thick, rigid or glass-filled sheet. Edge cracks and concave sides cause early failure. Machine these materials.
-
Using a dull or nicked die. Edge defects start tensile and impact failures. Inspect dies, and sharpen or replace them as needed.
-
Cutting an 80 mm bar from a Type B specimen. Its 60 mm parallel section is too short.
-
Ignoring flow direction. Moulded specimens are tested along the flow. Bars cut from plaques or sheet need their orientation recorded.
-
Skipping conditioning, especially for polyamides and other hygroscopic grades.
-
Measuring modulus from crosshead travel instead of an extensometer.
-
Mixing ISO and ASTM specimens in one data set. The results are not interchangeable.
ISO 3167 vs ASTM D638 and ISO 20753
-
ASTM D638: The US tensile method, see our ASTM D638 guide. Its common Type I specimen is about 165 mm long, 13 mm wide in the narrow section and typically 3.2 mm thick, with a 50 mm gauge length. ASTM flex and impact bars follow their own standards (ASTM D790, D256), and specimen moulding is covered separately (ASTM D3641). ASTM has no equivalent to the single multipurpose specimen concept.
-
ISO 527-2: Defines the Type 1A and 1B tensile specimens that match ISO 3167 Types A and B, along with the test conditions.
-
ISO 20753: The newer specimen standard that ISO intends to replace ISO 3167. Its Type A1 (moulded) and A2 (machined) tensile specimens carry the multipurpose concept forward, and it also defines bars, small tensile specimens and plates.
-
ISO 294-1: Moulds and moulding conditions for the A1 multipurpose specimen and B1 bar.
-
ISO 10350-1 and ISO 11403: Rules for comparable single-point and multipoint data that rely on multipurpose specimens.
Equipment summary
-
ISO 3167 Type A specimen cutter with ejector, for thinner and softer sheet. Type B and custom outlines are available on request. See cutting dies.
-
Presses: Arbor presses (8, 17 and 26 kN manual, 100 kN air-hydraulic) and the die press range. Free test cuts are available.
-
Tensile testing: Galdabini benchtop universal testing machines from 2.5 to 100 kN, or the Mark-10 F1505 for QC strength checks.
-
Grips: Wedge grips, pneumatic grips and tensile grips.
-
Strain: Clip-on extensometers and video extensometers.
-
Bars: Bend testing fixtures for ISO 178 and compression platens for ISO 604.
-
More on our plastics page and the ISO standards hub.
ISO 3167 FAQ
What is ISO 3167?
ISO 3167 specifies the multipurpose test specimen for plastics. It is a 10 × 4 mm dumbbell that can be tensile tested directly or cut into bars for flexural, impact, heat deflection and other tests, so that all properties come from one specimen geometry and moulding history.
What is the current edition of ISO 3167?
The current edition is ISO 3167:2014, the fifth edition, which ISO confirmed in 2026. ISO intends it to be gradually replaced by ISO 20753, so check which one your customer or material standard calls up.
What are the dimensions of the ISO 3167 Type A specimen?
Type A is 170 mm long, with an 80 mm parallel section 10.0 mm wide, 20.0 mm wide ends and 4.0 mm thickness. It matches the ISO 527-2 Type 1A tensile specimen.
What is the difference between Type A and Type B?
Both share the 10 × 4 mm cross-section and 20 mm ends. Type A has a short shoulder radius and an 80 mm parallel section and is used for moulded specimens. Type B has a 60 mm radius and a 60 mm parallel section, matches ISO 527-2 Type 1B and is used for machined specimens.
How are multipurpose specimens normally made?
Normally by injection moulding to ISO 294-1, or by compression moulding (ISO 293 or ISO 295) and machining to ISO 2818. ISO 3167 covers these routes in Clause 4.
Can I die-cut ISO 3167 specimens?
For thinner and softer ductile sheet, yes. A sharp specimen cutter gives consistent 1A-shaped tensile specimens. For thick, rigid, brittle or glass-filled materials, machine the specimens instead, because die cutting can crack or taper the edges. Always report that specimens were die-cut from sheet.
Is ISO 3167 Type A the same as ISO 527-2 Type 1A?
Yes, the geometry is the same. ISO 3167 defines the specimen and its preparation, and ISO 527-2 defines how to run the tensile test on it.
Which tests use bars cut from the multipurpose specimen?
The 80 × 10 × 4 mm bar from the Type A centre section is used for ISO 178 flexural, ISO 179-1 Charpy, ISO 180 Izod and ISO 75-2 heat deflection tests. Shorter pieces can be used for ISO 604 compression and ISO 306 Vicat tests.
What test speed is used for the tensile test?
ISO 527-2 measures modulus at 1 mm/min on Type 1A and 1B specimens, then strength usually at 5 mm/min for brittle materials or 50 mm/min for ductile ones, as set by the material standard.
What load capacity do I need?
The cross-section is 40 mm², so force equals strength × 40. That is about 1.5 kN for PP, about 3 kN for engineering plastics and up to about 7 kN for glass-filled grades. A 5 or 10 kN universal testing machine covers most work, and 25 kN gives headroom.
How does ISO 3167 compare with ASTM D638?
ASTM D638 Type I is about 165 mm long, 13 mm wide and typically 3.2 mm thick, and ASTM uses separate flex and impact bars. ISO 3167 uses one 10 × 4 mm multipurpose specimen for all of them. Results are not interchangeable.
Does Universal Grip make an ISO 3167 specimen cutter?
Yes. Our ISO 3167 Specimen Cutter is a hardened, precision-ground Type A dumbbell die with a spring-loaded ejector, for thin to moderate plastic sheet in manual, toggle or pneumatic presses. Type B and custom outlines are available on request, and we offer free test cuts.
Need a fixture, grips or a complete test system for ISO 3167? Contact Universal Grip with your material, specimen size and machine connection and we will quote the right setup.
