ISO 6259-3
Tensile Test for Polyolefin Pipes (PE, PE-X, PP, PB)

Written by Chris Thomas, Universal Grip Company · Reviewed by Frank Bertini · Updated October 31, 2026
ISO 6259-3 is the International Standard method for measuring the tensile properties of polyolefin pipes: polyethylene (PE), cross-linked polyethylene (PE-X), polypropylene (PP) and polybutene (PB). Dumbbell test pieces are die-cut or machined from the pipe wall and pulled to break. The test reports two numbers, stress at yield and elongation at break. Pipe extruders use it for quality control, and pipe product standards for gas and water distribution call it up when they set a minimum elongation at break.
It looks like an ordinary plastics tensile test, but it is easy to get wrong. The test piece type, preparation method and test speed all change with wall thickness. The specimens are curved because they come from a round pipe. Polyolefins can stretch several hundred percent before they break, so the grips have to hold through a long draw and the test frame needs plenty of travel. This guide covers how test pieces are selected and prepared, conditioning, speeds, machine and grip choice, a worked calculation, common errors and how ISO 6259-3 relates to ISO 527 and ASTM D638.
ISO 6259-3 at a glance
-
Current edition: ISO 6259-3:2015 (second edition, replacing ISO 6259-3:1997). ISO confirmed it in 2026 and has also registered a revision project, so check for a newer edition before you write a procedure around it.
-
Scope: Tensile properties of polyolefin pipes: PE, PE-X, PP and PB.
-
General method: ISO 6259-1:2015 (Thermoplastics pipes — Determination of tensile properties — Part 1: General test method). Part 3 gives the polyolefin-specific details and refers to Part 1 for the apparatus, conditioning, procedure, results and report.
-
Test pieces: Type 1 (same shape as ISO 527-2 Type 1B), Type 2 (same as the ISO 6259-2 Type 2) and Type 3 (same as Type B in ISO 13953). The thickness is always the full pipe wall thickness.
-
Preparation: Die cutting or machining. Walls up to 12 mm are preferably die-cut; walls over 12 mm are preferably machined.
-
Test speed: Set by wall thickness and test piece type, from 100 mm/min for thin walls down to slower speeds for thick walls (see below).
-
Results: Stress at yield (MPa) and elongation at break (%).
-
Informative annexes: Basic specifications for PE (Annex A), PE-X (Annex B), PP (Annex C) and PB (Annex D).
-
Related standards: ISO 6259-1, ISO 6259-2 (PVC pipes), ISO 527-1, ISO 527-2, ISO 13953 (butt-fusion joint tensile test), and pipe product standards such as ISO 4427-2 and ISO 4437-2.
What ISO 6259-3 measures and who uses it
The test pulls a dumbbell taken from the pipe wall at constant crosshead speed until it breaks. Polyolefin pipe grades are ductile. The test piece reaches a yield peak, a neck forms, and the neck then travels along the narrow section as the material cold-draws. Stress at yield is the force at that first peak divided by the original cross-section. Elongation at break is how far the gauge marks have separated at fracture, as a percentage of the original gauge length.
Elongation at break is a sensitive way to check that the pipe was processed correctly. Degraded or contaminated melt, poor homogenisation, voids, inclusions and insufficient stabilisation all tend to cut elongation sharply. Yield stress changes much less. That is why pipe specifications for PE water and gas pipe usually set a minimum elongation at break (the informative Annex A basic specification for PE has long been a mean above 350 %) rather than a strength value. The standard is explicit that this is a short-term material and process control test. It does not measure long-term pipe performance, which needs hydrostatic pressure, slow crack growth and other tests.
Typical users include:
-
PE, PE-X, PP and PB pipe extruders running batch release and process control testing
-
Gas and water utilities and their third-party inspection labs checking incoming pipe
-
Certification bodies and accredited labs running type tests against ISO 4427, ISO 4437, EN 12201, EN 1555 and similar product standards
-
Compound and resin suppliers qualifying pipe grades
-
Plumbing and heating system makers testing PE-X, PP and PB pipe
Test pieces: types, dimensions and selection
ISO 6259-3 defines three test piece shapes. In every case the thickness is the wall thickness of the pipe. The test piece is taken along the pipe axis and keeps the pipe's curvature. It is not flattened.
Type 1 (ISO 527-2 Type 1B shape)
-
Overall length: 150 mm minimum
-
Width of ends: 20 ± 1 mm. ISO 6259-3:2015 notes that the end width can be increased to suit thicker walls (B = e + 15 mm, where e is the wall thickness) to reduce slippage in the grips.
-
Narrow parallel portion: 60 ± 1 mm long, 10 mm wide (tolerance ± 0.2 mm)
-
Radius: 60 ± 1 mm
-
Gauge length: 50 ± 1 mm
-
Initial distance between grips: 115 ± 5 mm
Type 2 (thin walls)
-
Overall length: 115 mm minimum
-
Width of ends: 25 ± 1 mm
-
Narrow parallel portion: 33 ± 2 mm long, 6 mm wide (tolerance +0.4/0 mm)
-
Small radius 14 ± 1 mm, large radius 25 ± 2 mm
-
Gauge length: 25 ± 1 mm
-
Initial distance between grips: 80 ± 5 mm
Type 3 (thick walls, pin-loaded)
Type 3 is a large machined test piece, the same as Type B of ISO 13953. It has a wide, short narrow section and is loaded through holes and loading pins, not clamped at the ends. In the 1997 edition it measured at least 250 mm long with 100 mm wide ends and a 25 mm wide narrow section. Take the current dimensions from the 2015 edition.
Which type, which method, which speed
Test piece type, preparation method and speed all follow from the nominal wall thickness e. The selection table in the standard (unchanged in structure from the 1997 edition) works out as follows. Confirm the exact speeds and boundaries against your copy of the current edition.
-
e ≤ 5 mm: Type 2, die-cut or machined, 100 mm/min
-
5 mm < e ≤ 12 mm: Type 1, die-cut or machined, 50 mm/min
-
e > 12 mm: Type 1 machined at 25 mm/min, or Type 3 machined at 10 mm/min
Other speeds may be used if you can show they correlate with the specified speed, but in a dispute the specified speed governs.
Preparing test pieces from the pipe
-
Cut strips along the pipe axis, spaced evenly around the circumference. ISO 6259-1 sets the number of strips and test pieces according to the nominal outside diameter, so check its table for your pipe size. Take each test piece from the centre of its strip.
-
Die cutting (preferred up to 12 mm wall): use a sharp die with the Type 1 or Type 2 outline. Apply steady, continuous pressure in one stroke. ISO 6259-3 warns that careless die cutting can damage the test piece or give non-parallel sides, which is why die condition matters. A cutting die in an arbor press is the usual setup.
-
Machining (preferred over 12 mm wall): mill or route the profile following ISO 6259-1. Avoid overheating the polyolefin, and leave no tool marks or notches in the narrow section.
-
Do not flatten or heat-straighten the curved strip. Keep the inside and outside pipe surfaces as they are, because the outer skin is part of what the test checks.
-
Before testing, mark the gauge length and measure the width and wall thickness of the narrow section at several points. Use the minimum thickness for the cross-section calculation unless your procedure says otherwise.
Conditioning and test atmosphere
ISO 6259-3 takes conditioning from ISO 6259-1. Test pieces are conditioned at the test temperature, normally 23 °C, for a time that increases with wall thickness, so thick-walled pipe needs much longer than thin tubing. Take the exact times and tolerances from Clause 7 of ISO 6259-1, and test in the same atmosphere. Product standards and customer specifications may also set a minimum age for the pipe after extrusion before it is tested, so check those as well.
Test speed and machine requirements
The machine has to run at a constant crosshead speed of 100, 50, 25 or 10 mm/min, measure force accurately, and travel far enough for a ductile polyolefin to cold-draw to failure. ISO 6259-1 refers to ISO 7500-1 for verifying the force-measuring system. Elongation is measured between gauge marks, either with a long-travel extensometer, a video extensometer, or by measuring the marks. Typical forces are modest, and they scale with wall thickness:
-
Type 2, 5 mm wall: about 30 mm² cross-section, so a yield force well under 1 kN for PE
-
Type 1, 12 mm wall: about 120 mm², roughly 3 kN at yield for PE100
-
Type 1, 30 mm wall (machined): about 300 mm², roughly 7 to 8 kN
-
Type 3, thick walls: 25 mm × wall thickness, which can mean tens of kN
Crosshead travel matters as much as capacity. Most of the elongation happens after yield as the neck draws out, and a PE test piece passing 350 % to 600 % elongation needs several hundred millimetres of crosshead movement.
The Universal Grip ISO 6259-3 tensile fixture
Our ISO 6259-3 Tensile Fixture (part ref. UGC-ISO6259-3-TF) is a pair of screw-actuated tensile fixtures for dumbbell specimens cut from polyolefin pipe walls. Twin clamping plates close on the specimen ends by a knurled screw. An engraved centring scale and an open slot keep curved pipe-wall test pieces aligned on the load axis through yield and the long extension to break.
-
Twin clamping plates close symmetrically by knurled hand screw, so the curved test piece stays centred
-
Serrated faces on the clamping plates bite into the polyolefin ends to resist slippage
-
Engraved centring scale aligns specimens on the load axis
-
Open slot accommodates curved specimens cut from pipe walls
-
Long-travel design suits high-elongation polyolefins
-
Load capacity 10 kN typical, with higher capacities on request
-
Corrosion-protected steel construction
-
Pin spigot with lock nut, supplied with adapters to suit your load frame (clevis or threaded), for electromechanical universal test machines
-
Supplied as a pair
When ordering, give us your pipe diameter and wall thickness, the test piece type, the capacity you need and your test machine connection. A 10 kN pair covers Type 1 and Type 2 test pieces across most PE, PP, PE-X and PB pipe. For very thick machined walls, ask for a higher capacity. Type 3 test pieces are pin-loaded through holes, so tell us if your program includes Type 3 and we will advise on the right loading arrangement. See our tensile grips and vise grips for related clamp designs, or contact us with your pipe sizes.
Choosing a testing machine
Mark-10 motorized testers for QC
For thin and medium walls, a Mark-10 F-series motorized tester is a practical, lower-cost QC station at the extrusion line. Choose the long-stroke models. The F755 (750 lbF ≈ 3.3 kN) and F1505 (1,500 lbF ≈ 6.7 kN) have 813 mm of travel and a 10–600 mm/min speed range, which covers 100, 50, 25 and 10 mm/min. The F105, F305 and F505 have enough force for Type 2 test pieces, but their 457 mm travel can run short on high-elongation PE. The F1505 is the better fit for Type 1 test pieces up to about 12 mm wall. Speed accuracy is ±0.2 % and sampling runs at 5,000 Hz.
Galdabini universal testing machines for thick walls and accredited work
Use a Galdabini universal testing machine for thick-walled pipe, Type 3 test pieces, or an accredited lab that needs full ISO 7500-1 verification, extensometry and reporting. A 10 kN or 25 kN benchtop frame covers most Type 1 work. A 50 kN or 100 kN frame suits large-diameter, thick-walled pipe and Type 3 test pieces. Environmental chambers (−80 to +280 °C) support development testing away from 23 °C.
Extensometers
Elongation at break on polyolefins means following gauge marks through hundreds of percent of strain. A standard clip-on extensometer cannot do this, and one left on through break can be damaged. Practical options are a non-contact video extensometer, which tracks the gauge marks all the way to break, or an XL long-travel extensometer. Crosshead displacement on its own includes strain from the shoulders and any slip in the grips, so it overstates elongation. Use it only where your procedure accepts it, and say so in the report.
Step-by-step ISO 6259-3 procedure
-
1. Identify the pipe: material (PE, PE-X, PP or PB), nominal outside diameter, nominal wall thickness and production date or lot.
-
2. Select type, method and speed from the wall thickness: Type 2 at 100 mm/min up to 5 mm wall, Type 1 at 50 mm/min up to 12 mm wall, Type 1 at 25 mm/min or Type 3 at 10 mm/min above that.
-
3. Cut strips along the pipe axis, evenly around the circumference, in the number required by ISO 6259-1 for that diameter.
-
4. Prepare test pieces by die cutting (preferred ≤ 12 mm) or machining (preferred > 12 mm). Inspect the narrow section for nicks, burrs and non-parallel sides.
-
5. Mark gauge lengths (50 mm for Type 1, 25 mm for Type 2) and measure width and thickness in the narrow section.
-
6. Condition at the test temperature for the time set by ISO 6259-1 for that wall thickness.
-
7. Mount the test piece in the grips using the centring scale, set the initial grip separation (115 mm for Type 1, 80 mm for Type 2) and tighten both clamps evenly. Attach the extensometer or set up video tracking.
-
8. Run the test at the selected speed until fracture. Record the yield peak force and the gauge-mark separation at break.
-
9. Check the break. Note any test piece that slipped, broke at the grip or broke from a visible flaw. Retests follow the rules in ISO 6259-1.
-
10. Calculate and report stress at yield and elongation at break for each test piece, then the mean and the individual values the product standard asks for.
Calculations with a worked example
Stress at yield: σy = Fy / (b × e), where Fy is the force at yield (N), b is the width of the narrow section (mm) and e is the measured thickness (mm). The result is in MPa.
Elongation at break: εb = 100 × (Lu − L0) / L0, where L0 is the original gauge length and Lu is the distance between the gauge marks at break, both in mm. The result is in percent.
Worked example: A PE100 pipe, 110 mm outside diameter with a 10 mm nominal wall, falls in the 5 to 12 mm band, so the test uses Type 1 test pieces at 50 mm/min.
-
Measured width b = 10.02 mm, thickness e = 9.96 mm, so A = 10.02 × 9.96 = 99.80 mm²
-
Yield peak Fy = 2,365 N, so σy = 2,365 / 99.80 = 23.7 MPa
-
Gauge length L0 = 50 mm; gauge marks at break Lu = 290 mm, so εb = 100 × (290 − 50) / 50 = 480 %
-
Five test pieces give yield stresses of 23.7, 23.4, 23.9, 23.5 and 23.8 MPa, a mean of 23.7 MPa (23.66 before rounding)
-
Their elongations at break are 480, 520, 455, 610 and 505 %, a mean of 514 %. That is comfortably above the 350 % commonly specified for PE pipe, and every individual value also exceeds it.
At about 2.4 kN, this test fits a 10 kN fixture and an F1505 tester.
Typical results and what to report
PE80 and PE100 pipe grades typically show stress at yield of roughly 18 to 26 MPa at 23 °C. Elongation at break in good pipe is commonly well above 350 %, and often 500 % or more. PP and PB grades yield at different stress levels, and PE-X usually draws less than thermoplastic PE. Always compare against the product standard or the material data, not a generic figure. The test report follows ISO 6259-1 and normally includes:
-
A reference to ISO 6259-3 and ISO 6259-1, with editions
-
Full pipe identification: material, nominal diameter, wall thickness, manufacturer, lot or date
-
Test piece type, preparation method (die-cut or machined) and number of test pieces
-
Conditioning time and temperature, plus the test temperature
-
Test speed
-
Individual and mean values of stress at yield and elongation at break
-
Any test pieces discarded or retested, with the reason (slip, grip break, flaw)
-
How elongation was measured (extensometer type or gauge marks)
-
Test date and any deviations
Common errors
-
Wrong type or speed for the wall thickness. Running a 15 mm wall at 50 mm/min, or a 4 mm wall as Type 1, gives results that cannot be compared and invites a dispute.
-
Dull or damaged dies. A worn edge leaves nicks and tapered sides, and these start premature breaks with low elongation. Inspect and sharpen dies regularly.
-
Flattening curved strips. This puts strain into the test piece before the test even starts. Test it curved and use grips designed for curved test pieces.
-
Off-axis gripping. A curved test piece clamped off-centre bends as it loads. Use a centring scale and tighten both plates symmetrically.
-
Slippage at the ends. Thick or very slippery polyolefins can creep out of smooth jaws. Use serrated faces, widen the ends (B = e + 15 mm) and re-tighten after seating.
-
Elongation from crosshead travel. This includes shoulder strain and grip slip and overstates εb. Use gauge marks with a video or long-travel extensometer.
-
Not enough travel. If the frame runs out of stroke before break, you have no valid elongation at break result.
-
Short conditioning on thick walls. The core of a thick strip stays warm long after the surface has cooled, and warm test pieces give a low yield stress.
ISO 6259-3 vs ASTM D638, ISO 527 and related standards
-
ISO 6259-1: The general method for all thermoplastics pipes. Part 3 cannot be used without it.
-
ISO 6259-2: The equivalent part for PVC-U, PVC-O, PVC-C and PVC-HI pipes, which uses different test piece types and speeds.
-
ISO 527-1 and ISO 527-2: ISO 6259 is based on ISO 527-1, adapted for curved test pieces that can be much thicker than the few millimetres ISO 527 assumes. The Type 1 shape is the ISO 527-2 Type 1B dumbbell, but ISO 527 test conditions (modulus at 1 mm/min, 4 mm thick specimens) do not apply to pipe test pieces.
-
ASTM D638: The closest ASTM method is ASTM D638. North American PE material and pipe specifications, such as ASTM D3350, reference D638 for tensile properties. Specimen shapes, gauge lengths and speeds differ from ISO 6259-3, so the results are not interchangeable.
-
ISO 13953: The tensile test for butt-fusion joints in PE pipe. ISO 6259-3 Type 3 shares its Type B test piece geometry.
-
Product standards: ISO 4427-2 (PE water pipe), ISO 4437-2 (PE gas pipe), EN 12201-2 and EN 1555-2 call up ISO 6259-1 and ISO 6259-3 for elongation at break.
Equipment summary
-
ISO 6259-3 screw-clamp tensile fixture, supplied as a pair, 10 kN typical. See tensile grips and contact us with your pipe sizes.
-
Specimen preparation: Type 1 and Type 2 cutting dies (hardened or ribbon steel) and arbor presses (8, 17 and 26 kN manual, 100 kN air-hydraulic). Free test cuts are available.
-
Lab frames: Galdabini benchtop universal testing machines from 2.5 to 100 kN, plus floor-standing models for larger loads.
-
Strain measurement: Video extensometers and XL long-travel extensometers.
-
Temperature: Environmental chambers from −80 to +280 °C.
-
More plastics standards and fixtures are on our plastics page and the ISO standards hub.
ISO 6259-3 FAQ
What is ISO 6259-3?
ISO 6259-3 is the ISO method for the tensile properties of polyolefin pipes (PE, PE-X, PP and PB). Dumbbell test pieces are die-cut or machined from the pipe wall and pulled to break to measure stress at yield and elongation at break. It is used together with the general method in ISO 6259-1.
What is the current edition of ISO 6259-3?
The current edition is ISO 6259-3:2015, the second edition, which replaced the 1997 edition. ISO confirmed it in 2026 and has a revision project registered, so check for a newer edition before updating procedures.
Which test piece type should I use?
It depends on the nominal wall thickness. Use Type 2 for walls up to 5 mm, Type 1 for walls over 5 mm up to 12 mm, and machined Type 1 or Type 3 for walls over 12 mm. Confirm the boundaries in the current edition.
What test speed does ISO 6259-3 use?
The speed follows wall thickness and type: 100 mm/min for Type 2 test pieces (wall up to 5 mm), 50 mm/min for Type 1 up to 12 mm, and 25 mm/min for Type 1 or 10 mm/min for Type 3 on thicker walls. Other speeds are allowed only if you can show they correlate, and the specified speed governs in a dispute.
Should pipe test pieces be die-cut or machined?
ISO 6259-3:2015 says test pieces up to 12 mm wall are preferably die-cut and those over 12 mm are preferably machined. Die-cutting is faster but needs a sharp die and steady pressure to avoid damaged or non-parallel sides.
Do I flatten the curved test piece before testing?
No. The test piece keeps the curvature of the pipe wall and its full wall thickness. Use grips that centre and clamp curved test pieces instead of flattening them.
What elongation at break is required for PE pipe?
The informative Annex A of ISO 6259-3 gives a basic specification for polyethylene (a mean above 350 % in the 1997 text), and 350 % is the figure most PE pipe standards use. Pipe product standards such as ISO 4427-2 and ISO 4437-2 set the binding requirement, so follow the one that applies to your pipe.
How is elongation at break calculated?
Elongation at break = 100 × (Lu − L0) / L0, where L0 is the original gauge length (50 mm for Type 1, 25 mm for Type 2) and Lu is the distance between the gauge marks at break. Measure it with a video or long-travel extensometer, or from the gauge marks, not from crosshead travel.
What load capacity do I need?
Most Type 1 and Type 2 test pieces yield well below 10 kN. A 12 mm wall Type 1 PE100 test piece is around 3 kN. Thick machined walls and Type 3 test pieces can need tens of kN, which calls for a 25 to 100 kN universal testing machine.
Can a Mark-10 tester run ISO 6259-3?
Yes, for thin and medium walls. The F755 and F1505 offer 3.3 and 6.7 kN, 813 mm of travel and 10 to 600 mm/min, which covers all four standard speeds. For thick walls, Type 3 or accredited lab work, use a Galdabini universal testing machine.
Is ISO 6259-3 the same as ASTM D638?
No. Both are dumbbell tensile tests, but ISO 6259-3 uses pipe-wall test pieces at full wall thickness with speeds set by thickness. ASTM D638 uses its own specimen types and speeds, so results are not directly interchangeable.
Does Universal Grip make a fixture for ISO 6259-3?
Yes. Our ISO 6259-3 Tensile Fixture is a pair of screw-clamp grips with serrated twin clamping plates, a centring scale and an open slot for curved pipe-wall specimens, rated 10 kN typical with higher capacities on request. Send us your pipe sizes and machine connection for a quote.
Need a fixture, grips or a complete test system for ISO 6259-3? Contact Universal Grip with your material, specimen size and machine connection and we will quote the right setup.
