Home › Products › Puncture Fixtures › XY Adjustable Puncture Fixture





XY Adjustable Puncture Fixture – Multi-Point Testing
Puncture fixture on a manual XY cross table, so you can place several test points on one clamped specimen without taking it out of the fixture.
Brand: Universal Grip | Model: UGC-PF-150 | ● Configured to order
Manual XY cross table with hand cranks positions each test point
Several punctures on one specimen without re-clamping
Four toggle clamps hold the specimen plate in place
Interchangeable insert rings set the free test diameter
Upper probe holder carries the puncture pin
Built around your specimen geometry and test pattern on request
Downloads and standards
Trusted by Global Companies


























Puncture fixture with XY cross table for multi-point tests
The UGC-PF-150 is built for specimens that need more than one puncture. Its specimen carrier sits on a manual XY cross table, so you can step from one test point to the next with the hand cranks while the part stays clamped. That saves handling time and keeps every point referenced to the same setup, which matters when you are mapping puncture resistance across a lid, membrane or board.
How it works
The specimen lies on a plate and is held down by four toggle clamps. An interchangeable insert ring under the specimen defines the free diameter around each test point: a small ring gives a stiff, tightly supported span, a larger ring lets the material deflect more before the pin breaks through. The puncture pin is held in a probe holder on the upper adapter and is driven down by the testing machine while force and travel are recorded. After each test you crank the table to the next position and repeat. A round base keeps the assembly stable on the machine.
Built to your specimen
This fixture is normally configured around a specific part or test plan, so maximum load, XY travel and coupling are agreed at quote stage. When you ask for a quote, tell us:
Specimen size and thickness
Number and spacing of test points
Insert ring diameters you need
Probe or pin geometry
Your machine coupling
Typical applications
Electronic boards and panels
Membranes and films
Packaging lids
Multi-point puncture mapping
If you only need one puncture per specimen, a fixed fixture from our puncture fixtures range is simpler. Choose the UGC-PF-150 when repeat positioning on one specimen is the point of the test.
Machine fit
Because the load depends on your pin and specimen, we size the fixture and the frame together. Lower-force work on films and lids often runs on a Mark-10 motorized tester from our tensile testers range; stiffer boards and panels go on a Galdabini benchtop UTM. Adapters are available to match the fixture to an existing frame. See puncture testing for complete setups.
Send us your specimen and test-point layout and we will design and quote the fixture.
XY Adjustable Puncture Fixture Specifications
TEST TYPE
Puncture, multi-point
POSITIONING
Manual XY cross table, hand cranks
SPECIMEN CLAMPING
4 toggle clamps
INSERT RINGS
Interchangeable, various diameters
PROBE
Puncture pin in upper probe holder
BASE
Round base
MAX. LOAD
On request
TRAVEL
On request
COUPLING
On request
MATERIAL
Steel and aluminum
PART REF.
UGC-PF-150
Models & Options
Insert rings — Interchangeable rings in the diameters your test needs (Specify at order)
Probe / pin geometry — Pin made to your method or drawing (Specify at order)
XY travel and test-point spacing — Table sized to your specimen and pattern (On request)
Machine coupling — Matched to your frame; adapters available (On request)
What's Included
Specimen carrier on a manual XY cross table with hand cranks
Specimen plate with four toggle clamps
Interchangeable insert rings in the diameters specified
Upper probe holder with puncture pin
Coupling and round base configured to your machine
Supported Test Standards
Standards list
Compatible Grips & Fixtures
Tensile Testers — Mark-10 motorized testers for lower-force puncture
Benchtop UTMs — Galdabini frames for boards and stiffer panels
Adapters — Couplings to fit an existing frame
Puncture Testing — Puncture setups and fixtures
Software — Test control and result reporting
“Customer quote”
Related Equipment
UGC-PF-140 Protective Clothing Needle Puncture Fixture
2 kN needle puncture fixture for protective clothing, gloves and medical needle tests, with a clamped specimen holder an
UGC-PF-160 Huber Needle Coring Fixture
Coring test fixture for non-coring Huber needles: the needle passes through a port septum and any cored fragments collec
UGC-PF-130 Punch Fixture 10 kN
Round-nosed punch-and-die fixture with three punch radii and three die holes for puncture and dome tests on sheets, film
UGC-PF-170 Food Packaging Foil Puncture Fixture JIS Z1707
Stainless steel needle puncture fixture for food packaging films to JIS Z 1707: a Ø 1 mm needle pierces film clamped ove
XY Adjustable Puncture Fixture FAQ
What does the XY table do?
It lets you move the clamped specimen with hand cranks so you can make several punctures on one specimen without re-clamping it.
How is the specimen held?
On a plate with four toggle clamps. Interchangeable insert rings underneath set the free test diameter.
What is the maximum load and travel?
Both are configured on request to your specimen, probe and test-point layout.
What kinds of parts is it used for?
Electronic boards and panels, membranes and films, packaging lids, and any job that needs puncture mapping across one part.
Which testing machine does it fit?
Coupling is matched to your frame. Mark-10 tensile testers suit lower-force work; Galdabini benchtop UTMs suit stiffer parts.
What should I send for a quote?
Specimen size, number and spacing of test points, ring diameters, probe geometry and your machine coupling.




