Home › Products › Puncture Fixtures › Punch Fixture 10 kN





Punch Fixture 10 kN – Interchangeable Punches and Dies
Round-nosed punch-and-die fixture with three punch radii and three die holes for puncture and dome tests on sheets, films and panels to 10 kN.
Brand: Universal Grip | Model: UGC-PF-130 | ● Configured to order
10 kN (about 2,250 lbf) maximum load for sheets, films and panels
Three round-nosed punches supplied: R15, R10 and R5 mm
Die holes of Ø 36, 26 and 16 mm, the two smaller set by insert plates
Change test geometry by swapping punch and insert, not the whole fixture
Nickel-plated steel body and punches resist corrosion
Female clevis coupling for a Ø 30 mm pin; other couplings via adapters
Downloads and standards
Trusted by Global Companies


























10 kN punch fixture with three punch-and-die geometries
The UGC-PF-130 is a general-purpose punch fixture for labs that push a rounded punch through, or into, a flat specimen and record force against displacement. It is rated to 10 kN (about 2,250 lbf), which covers rigid plastic sheet, composite laminates, packaging board and thin metal sheet. Instead of buying a separate fixture for every specimen thickness, you get three punch radii and three die holes on one base.
How it works
The specimen lies over a die hole in the lower base. A round-nosed punch on the crosshead comes down, presses the material into the hole and either domes it or punches through, depending on the material and how far you drive it. The base itself has a Ø 36 mm (1.42 in) hole for the R15 mm punch. Two insert plates drop into the base to reduce the hole to Ø 26 mm (1.02 in) or Ø 16 mm (0.63 in) for the R10 and R5 mm punches. Because only the punch and insert change, the base stays aligned on the machine between test series.
Punch and die combinations
R15 / Ø 36 mm – large punch working directly in the base hole, for thicker or stiffer panels.
R10 / Ø 26 mm – medium punch with insert plate.
R5 / Ø 16 mm – small punch with insert plate, for thin sheet and films where a tighter span is wanted.
If your method calls for a radius or hole size outside these three, a custom punch or insert can be made; send us the drawing or the clause of your test method.
Typical applications
Plastic sheets and panels
Composite laminates
Packaging materials
Thin metal sheets
For low-force film and membrane puncture, the other fixtures in our puncture fixtures range use needles, small probes and lighter construction. The UGC-PF-130 is the one to choose when you need a stiff, heavy punch and the 10 kN reserve.
Machine fit and coupling
A 10 kN rating is above the range of Mark-10 motorized testers, so the natural home for this fixture is a Galdabini benchtop frame such as the 10 kN UTM or the 25 kN UTM when you want headroom. The fixture is supplied with a female clevis for a Ø 30 mm (about 1.18 in) pin. If your load cell or crosshead uses a different connection, adapters are available. See puncture testing for how the fixture fits into a complete setup.
Tell us the punch and hole combinations you need, your specimen size and your machine coupling, and we will quote the fixture configured for your lab.
Punch Fixture 10 kN Specifications
MAX. LOAD
10 kN
TEST TYPE
Puncture / punch
PUNCH RADIUS
15 mm (10 mm and 5 mm also included)
DIE HOLE
Ø 36 mm (inserts Ø 26 mm and 16 mm)
PUNCH / HOLE COMBINATIONS
R15 / Ø 36 mm, R10 / Ø 26 mm, R5 / Ø 16 mm
COUPLING
Female clevis, Ø 30 mm pin
MATERIAL
Steel, nickel-plated
SCOPE OF SUPPLY
Fixture incl. 3 punches and 2 insert plates
DRAWINGS
Dimensional drawings and 3D models on request
PART REF.
UGC-PF-130
Models & Options
R15 / Ø 36 mm — Large punch working in the base hole (Specify at order)
R10 / Ø 26 mm — Medium punch with Ø 26 mm insert plate (Specify at order)
R5 / Ø 16 mm — Small punch with Ø 16 mm insert plate (Specify at order)
Custom punch or insert — Other radii or hole diameters to your test method (On request)
Coupling adapters — To fit the Ø 30 mm clevis to your machine (On request)
What's Included
Punch fixture base with Ø 36 mm die hole
Three round-nosed punches: R15, R10 and R5 mm
Two insert plates with Ø 26 mm and Ø 16 mm holes
Female clevis coupling for a Ø 30 mm pin; adapters quoted separately on request
Supported Test Standards
Standards list
Compatible Grips & Fixtures
10 kN Benchtop UTM — Galdabini frame matched to the 10 kN rating
25 kN Benchtop UTM — Extra capacity for stiff panels and laminates
Adapters — Fit the Ø 30 mm clevis to other couplings
Puncture Testing — Setups and fixtures for puncture tests
Plastics Testing — Fixtures and grips for plastic sheet and film
“Customer quote”
Related Equipment
UGC-PF-120 Fabric Stiffness Puncture Fixture
Circular bend fixture with 38.1 mm orifice and 25.4 mm flat plunger that measures fabric stiffness in all directions at
UGC-PF-140 Protective Clothing Needle Puncture Fixture
2 kN needle puncture fixture for protective clothing, gloves and medical needle tests, with a clamped specimen holder an
UGC-PF-110 Tissue Paper Ball Burst Fixture ISO 12625-9
Stainless steel ball burst fixture with water tray for dry and wet tissue, pneumatic (500 N) or manual (10 kN) clamping,
UGC-PF-150 XY Adjustable Puncture Fixture
Puncture fixture on a manual XY cross table, so you can place several test points on one clamped specimen without taking
Punch Fixture 10 kN FAQ
What is the maximum load of the UGC-PF-130?
10 kN, which is about 2,250 lbf.
Which punches and die holes come with it?
Three punches with R15, R10 and R5 mm noses, plus two insert plates that reduce the Ø 36 mm base hole to Ø 26 mm or Ø 16 mm.
Can I get a different punch radius or hole size?
Yes. Custom punches and inserts are made on request to the geometry in your test method.
What coupling does the fixture use?
A female clevis for a Ø 30 mm pin. Adapters are available for other machine connections.
Which testing machine should I use?
A Galdabini benchtop frame of 10 kN or more, such as the 10 kN UTM, suits the fixture's rating.
Is it tied to one test standard?
No. It is a general punch fixture for puncture and dome tests on sheets, films and panels; tell us your method and we will confirm the geometry.




