Home › Products › Puncture Fixtures › Huber Needle Coring Fixture





Huber Needle Coring Fixture – ASTM F3212
Coring test fixture for non-coring Huber needles: the needle passes through a port septum and any cored fragments collect in a clear chamber for inspection.
Brand: Universal Grip | Model: UGC-PF-160 | ● Configured to order
Used for coring tests on Huber needles to ASTM F3212
Transparent polycarbonate chamber collects cored fragments
Stainless steel 304 top plate holds the septum
Controlled insertion speed and force record in a testing machine
1 kN (about 225 lbf) capacity for needle penetration forces
Female clevis coupling for a Ø 15.9 mm (5/8 in) pin
Standards: ASTM F3212
Trusted by Global Companies


























Coring test fixture for Huber needles and port septa
The UGC-PF-160 is a test fixture for medical device labs that validate non-coring (Huber) needles and the septa of implanted ports. It is used for coring tests such as ASTM F3212, where the question is not only how much force the needle needs but whether it cuts fragments out of the septum on the way through. Capacity is 1 kN (about 225 lbf).
How it works
The septum is held in a stainless steel top plate. The needle, mounted on the testing machine crosshead, is driven through it at a set speed while force is recorded. Below the plate sits a transparent polycarbonate chamber, so any material cored from the septum falls into a clear, closed space where it can be seen and collected for counting or inspection. Running the insertion in a testing machine instead of by hand gives repeatable speed and alignment from one needle to the next, which is what makes results comparable across lots. The force curve and the fragment check for each needle can then be recorded together, so every needle in a validation run has its own traceable result.
Construction
Top plate in stainless steel 1.4301 (304)
Transparent polycarbonate collection chamber
Female clevis for a Ø 15.9 mm (5/8 in) pin on the lower fixture
Septum size and needle gauge are specified at order so the top plate fits your port design. Stainless steel and polycarbonate are easy to clean between test series, which keeps stray particles from an earlier needle out of the next fragment count.
Typical applications
Implanted port septa
Non-coring needles
Medical device validation
Infusion systems
For hypodermic needle puncture of protective clothing, gloves or closures, see the UGC-PF-140 needle puncture fixture; both sit in our puncture fixtures range.
Machine fit
Needle penetration forces are low, and the 1 kN rating fits a Mark-10 motorized tester such as the 300 lb tensile tester. Labs that need tighter speed control and full data records for validation files often choose a Galdabini 2.5 kN benchtop UTM with our test software. Adapters are available if your machine does not take a 5/8 in clevis.
Tell us your septum size, needle gauge and machine coupling and we will quote the fixture.
Huber Needle Coring Fixture Specifications
MAX. LOAD
1 kN
TEST TYPE
Needle coring / penetration
SPECIMEN
Huber needles, septa
SEPTUM HOLDER
Stainless steel top plate
CHAMBER
Transparent polycarbonate cylinder
COUPLING
Female clevis, Ø 15.9 mm (5/8 in) pin
MATERIAL
Stainless steel 1.4301 (304), polycarbonate
TEMPERATURE RANGE
On request
DRAWINGS
Dimensional drawings and 3D models on request
PART REF.
UGC-PF-160
Models & Options
Septum top plate — Made to your septum size (Specify at order)
Needle gauge — Set up for the Huber needle gauge you test (Specify at order)
Coupling adapters — For machines without a 5/8 in clevis (On request)
What's Included
Stainless steel 304 top plate to hold the septum
Transparent polycarbonate collection chamber
Female clevis coupling for a Ø 15.9 mm (5/8 in) pin
Needle mounting and septum fit confirmed at quote to your needle gauge and septum size
Supported Test Standards
ASTM F3212 — Coring testing of Huber needles
Compatible Grips & Fixtures
300 lb Tensile Tester — Mark-10 motorized tester covering the 1 kN rating
2.5 kN Benchtop UTM — Galdabini frame for medical device validation
UGC-PF-140 Needle Puncture Fixture — Needle puncture of PPE materials and closures
Software — Test control and validation records
Adapters — Couplings for other machine connections
“Customer quote”
Related Equipment
UGC-PF-140 Protective Clothing Needle Puncture Fixture
2 kN needle puncture fixture for protective clothing, gloves and medical needle tests, with a clamped specimen holder an
UGC-PF-150 XY Adjustable Puncture Fixture
Puncture fixture on a manual XY cross table, so you can place several test points on one clamped specimen without taking
UGC-PF-170 Food Packaging Foil Puncture Fixture JIS Z1707
Stainless steel needle puncture fixture for food packaging films to JIS Z 1707: a Ø 1 mm needle pierces film clamped ove
UGC-PF-180 Foot and Leg Protector Puncture Fixture ISO 20344
Nail puncture fixture for safety footwear soles and penetration-resistant inserts, with Ø 3 mm and Ø 4.5 mm test nails f
Huber Needle Coring Fixture FAQ
What test is the UGC-PF-160 used for?
Coring tests on non-coring (Huber) needles, such as ASTM F3212, where a needle is driven through a port septum and cored fragments are checked.
How are cored fragments collected?
They fall into a transparent polycarbonate chamber below the septum plate, where they can be seen and collected.
What is the load capacity?
1 kN, about 225 lbf.
What materials is it made of?
Stainless steel 1.4301 (304) and polycarbonate.
Which tester should I use?
A Mark-10 300 lb tensile tester covers the rating; a Galdabini 2.5 kN benchtop UTM suits validation work that needs full data records.
What do I need to specify?
Septum size, needle gauge and your machine coupling.




