top of page

Home  ›  Products  ›  Puncture Fixtures  ›  Tape Puncture Resistance Fixture

UGC-PF-210 tape puncture resistance fixture for ASTM D1000 Figure 9 by Universal Grip
UGC-PF-210 tape puncture resistance fixture for ASTM D1000 Figure 9 by Universal Grip
UGC-PF-210 Tape Puncture Resistance Fixture by Universal Grip, view 2
UGC-PF-210 Tape Puncture Resistance Fixture by Universal Grip, view 3
UGC-PF-210 Tape Puncture Resistance Fixture by Universal Grip, view 4

Tape Puncture Resistance Fixture – ASTM D1000 Fig. 9

Puncture resistance fixture for pressure-sensitive adhesive tapes, configured to ASTM D1000 Figure 9 for electrical insulating and wire harness tapes.

Brand: Universal Grip  |  Model: UGC-PF-210  |  ● Configured to order

  • Configured to ASTM D1000, Figure 9 puncture resistance test

  • Holds tape specimens across the test opening

  • Probe mounted on a clevis adapter on the crosshead

  • Records the peak force to puncture the tape backing

  • For electrical insulating, wire harness and other PSA tapes

  • Perforation version to a customer specification available

Standards: ASTM D1000

Trusted by Global Companies

ASTM D1000 puncture resistance fixture for adhesive tapes

The UGC-PF-210 is the fixture for the puncture resistance test on pressure-sensitive adhesive-coated tapes in ASTM D1000, Figure 9. Tape manufacturers and wire harness suppliers use it to qualify electrical insulating tapes, where a backing that punctures easily can expose a conductor. It turns a test that is often done with improvised tooling into a repeatable setup on a testing machine.

See our complete ASTM D1000 guide for specimen preparation, the other tests in the standard and how results are reported. This page covers the fixture hardware.

 

How it works

The tape specimen is held across the test opening of the fixture. A probe to ASTM D1000 Figure 9, mounted on a clevis adapter, is driven down into the backing by the testing machine. Force is recorded against travel and the peak force at puncture is reported. Because the probe and opening are fixed parts of the fixture, every specimen is loaded the same way, which makes lot-to-lot comparisons meaningful. The force-travel curve also shows how the backing behaves before it fails: a tape that stretches a long way before puncture behaves differently on a sharp wire end than one that breaks at a high force with little travel, even if the peak forces are similar.

 

Versions

  • ASTM D1000 Fig. 9 – tape puncture resistance fixture.

  • Perforation version – resistance-to-perforation fixture built to a customer specification, for automotive and other tape specs that define their own probe and support.

 

Typical applications

  • Electrical insulating tapes

  • Pressure-sensitive tapes

  • Wire harness tapes

  • Tape QC labs

The same lab will usually also need peel and tensile setups for D1000; see our peel fixtures and the adhesives page.

 

Machine fit

The maximum load is confirmed on request for your tape construction. Tape puncture is a low-force test, so a Mark-10 motorized tester such as the 100 lb tensile tester or a Galdabini 2.5 kN benchtop UTM is the usual choice; the Galdabini also runs the D1000 tensile and adhesion tests. The fixture has a female clevis for a Ø 15.9 mm (5/8 in) pin, and adapters are available.

Tell us the tape standard or specification, tape width and your machine coupling, and we will quote the fixture.

Product video

At a glance

  • Test type: Puncture resistance

  • Specimen: Pressure-sensitive adhesive tapes

  • Probe: Per ASTM D1000 Fig. 9

  • Probe mounting: Clevis adapter

  • Coupling: Female clevis, Ø 15.9 mm (5/8 in) pin

  • Max. load: On request

Tape Puncture Resistance Fixture Specifications

TEST TYPE

Puncture resistance

 

SPECIMEN

Pressure-sensitive adhesive tapes

 

PROBE

Per ASTM D1000 Fig. 9

 

PROBE MOUNTING

Clevis adapter

 

COUPLING

Female clevis, Ø 15.9 mm (5/8 in) pin

 

MAX. LOAD

On request

 

MATERIAL

Steel, nickel-plated (typical)

 

TEMPERATURE RANGE

On request

 

DRAWINGS

Dimensional drawings and 3D models on request

 

PART REF.

UGC-PF-210

 

Models & Options

  • ASTM D1000 Fig. 9 — Tape puncture resistance fixture (Specify at order)

  • Perforation version — Resistance-to-perforation fixture to customer specification (On request)

  • Coupling adapters — For machines without a 5/8 in clevis (On request)

What's Included

  • Tape puncture fixture holding the specimen across the test opening

  • Probe to ASTM D1000 Fig. 9 on a clevis adapter

  • Female clevis coupling for a Ø 15.9 mm (5/8 in) pin

Supported Test Standards

  • ASTM D1000 — Pressure-sensitive adhesive-coated tapes for electrical and electronic applications

Compatible Grips & Fixtures

“Customer quote”

Related Equipment

UGC-PF-200 Shade Net Ball Burst Fixture

UGC-PF-200 Shade Net Ball Burst Fixture

Ball burst fixture for HDPE woven shade nets: a Ø 50 mm plastic ball pushes through net clamped over a Ø 102 mm opening

UGC-PF-220 Glass Puncture Fixture and Cold Chamber Jaws

UGC-PF-220 Glass Puncture Fixture and Cold Chamber Jaws

Glass puncture fixture with a 500 mm long Ø 12.7 mm punch and adjustable 25 to 50 mm holder; blank-jaw version runs in a

UGC-PF-190 Fabric Stiffness Puncture Fixture Similar Method

UGC-PF-190 Fabric Stiffness Puncture Fixture Similar Method

Open-frame circular bend fixture for comparative fabric stiffness checks by a method similar to ASTM D4032, with orifice

UGC-PF-230 Sheet Metal Ball Punch Fixture ISO 8490

UGC-PF-230 Sheet Metal Ball Punch Fixture ISO 8490

Miniature ball punch deformation fixture for thin metal foil and sheet, based on the ASTM E643 and ISO 8490 test princip

Tape Puncture Resistance Fixture FAQ

Which test is the UGC-PF-210 built for?

The puncture resistance test on pressure-sensitive adhesive-coated tapes in ASTM D1000, Figure 9.

 

Where can I find the full D1000 procedure?

Our ASTM D1000 guide covers specimen preparation, the test sequence and reporting.

 

Can you build a fixture to our own tape specification?

Yes. A perforation version is built to customer specification for tape specs with their own probe and support.

 

What is the maximum load?

Confirmed on request for your tape construction.

 

Which tester should I use?

A Mark-10 100 lb tensile tester or a Galdabini 2.5 kN benchtop UTM.

 

What coupling does it use?

A female clevis for a Ø 15.9 mm (5/8 in) pin; adapters are available.

 

Need help configuring a puncture fixture?

Tell us your material, test standard and specimen size. We will recommend the frame, force sensor, grips and fixtures, and send a quote.

bottom of page