Home › Products › Peel Fixtures › Peel Test Table with Ball Guide





Peel Test Table with Ball Guide – 0.2 kN
Low-friction peel table whose carriage runs on a recirculating ball guide and follows the peel front, keeping the peel angle constant over 300 mm.
Brand: Universal Grip | Model: UGC-PL-030 | ● Configured to order
Recirculating ball linear guide for low-friction carriage travel
300 mm (about 11.8 in) guide length for long peel distances
Carriage follows the peel front so the peel angle stays constant
Friction adds little to the measured force at low loads
Rated for 0.2 kN (about 45 lbf); clevis couplings above and below
Heavy-duty 5 kN sliding adapter version available
Downloads and standards
Trusted by Global Companies


























Sliding peel table on a recirculating ball guide
The UGC-PL-030 is a peel test table for adhesive tapes, labels, laminates, flexible packaging and coated films. It is designed for labs that run constant-angle peel tests and want the lower attachment to move freely with the specimen instead of dragging against it. The table is rated for 0.2 kN (200 N, about 45 lbf) and has a 300 mm (about 11.8 in) guide length.
How it works
In a constant-angle peel test the point where the bond separates moves along the specimen as the test runs. If the specimen stays fixed, the angle between the peeled strip and the substrate changes. On the UGC-PL-030, the lower attachment rides on a carriage that travels horizontally on a recirculating ball guide. As the specimen peels, the carriage follows the peel front, so the angle set at the start is held to the end of the run.
Because the carriage runs on recirculating balls rather than a plain slide, friction contributes little to the force measured by the load cell. That matters at the low forces typical of tape and label peel, where a sticky slide could add a meaningful share of the reading.
Construction and mounting
Couplings: clevis couplings above and below, female clevis for a Ø 15.9 mm (5/8 in) pin to a male clevis, so the table fits between the machine connection and your grip or specimen plate.
Materials: a compact build from aluminum and steel parts.
Carriage attachment: the grip or specimen plate that mounts on the carriage is specified at order to suit your specimen.
Sliding adapter version
For heavier work, a 5 kN (about 1,124 lbf) sliding adapter version is available. It offers 0–48 mm (about 0–1.9 in) of travel, a Ø 25 mm pin clevis from male to female, an overall length of 243 mm (about 9.6 in) and nickel-plated steel construction.
Machine fit
At 0.2 kN, the peel table suits low-force frames such as our 100 lb tensile tester and Galdabini benchtop universal testing machines fitted with a low-capacity load cell. For other machine connections, see our adapters. Fixed-geometry alternatives are listed on our peel fixtures page, including the UGC-PL-020 90° peel accessory.
Tell us the load rating you need, your machine coupling and the grip or specimen plate to mount on the carriage, and we will configure the table. Request a quote.
Peel Test Table with Ball Guide Specifications
MAX. LOAD
0.2 kN (200 N, approx. 45 lbf)
TEST TYPE
Peel, constant angle
GUIDE
Recirculating ball linear guide
GUIDE LENGTH
300 mm (approx. 11.8 in)
COUPLING
Female clevis Ø 15.9 mm (5/8 in) pin to male clevis, upper/lower
MATERIAL
Aluminum and steel
TEMPERATURE RANGE
Ambient
CARRIAGE ATTACHMENT
Grip or specimen plate specified at order
SLIDING ADAPTER VERSION
5 kN, 0–48 mm travel, Ø 25 mm pin clevis, 243 mm long
DRAWINGS
Dimensional drawings and 3D models on request
PART REF.
UGC-PL-030
Models & Options
Peel table — Recirculating ball guide, 300 mm guide length, rated 0.2 kN (Specify at order)
Sliding adapter — 5 kN, 0–48 mm travel, Ø 25 mm pin clevis (male to female), 243 mm long, nickel-plated steel (Specify at order)
Carriage grip or specimen plate — Attachment on the carriage to suit your specimen (On request)
Machine coupling — Adapters to other machine connections (On request)
What's Included
Peel table with carriage on a recirculating ball guide, 300 mm guide length (or the sliding adapter version, if ordered)
Clevis couplings above and below
Grip or specimen plate for the carriage specified at order; confirm scope on your quote
Supported Test Standards
Standards list
Compatible Grips & Fixtures
100 lb Tensile Tester — Low-force motorized frame for the 0.2 kN range
UGC-PL-020 90 Degree Peel Accessory — Base plate accessory with guide rod for 90° peel
UGC-PL-100 90 Degree Peel Grip 25 mm Roller — Compact 90° peel grip with Ø 25 mm roller
Vise Grips — Grip for the peeled strip
Adapters — Couplings for other machine connections
Peel Testing — Overview of peel test methods
“Customer quote”
Related Equipment
UGC-PL-020 90 Degree Peel Accessory
Flat base plate fixture with a height-adjustable guide rod that holds the peel line while an upper grip pulls the free s
UGC-PL-100 90 Degree Peel Grip 25 mm Roller
Compact 500 N peel grip that holds the rigid substrate under a height-adjustable Ø 25 mm roller for 90° peel tests on st
UGC-PL-040 Yogurt Cup Peel Fixture
Vacuum cup holder on a graduated tilting segment for lid peel and seal strength tests on yogurt cups and similar sealed
UGC-PL-010 T-Peel Fixture for Medical Packaging
Supported 90° T-peel fixture, rated to 100 N, that holds the specimen tail at 90° for seal strength tests on medical and
Peel Test Table with Ball Guide FAQ
Why use a sliding peel table?
The peel front moves along the specimen during a test. On the UGC-PL-030 the carriage follows it, so the peel angle set at the start stays constant to the end.
Does the ball guide affect the measured force?
Very little. The recirculating ball guide keeps friction low, which matters at the small forces typical of tape and label peel.
What is the load rating and guide length?
The peel table is rated for 0.2 kN (about 45 lbf) with a 300 mm guide length. A 5 kN sliding adapter version with 0–48 mm travel is also available.
How does it connect to the machine?
With clevis couplings above and below: a female clevis for a Ø 15.9 mm (5/8 in) pin to a male clevis. Other connections via our adapters.
What mounts on the carriage?
A grip or specimen plate chosen for your specimen; specify it when ordering.
Which testing machine suits it?
A low-force frame such as our 100 lb tensile tester, or a benchtop machine with a low-capacity load cell. Contact us with your model.




