Home › Products › Shear Fixtures › Double Shear Fastener Fixture NASM 1312-13





Double Shear Fastener Fixture NASM 1312-13
Compression-mode double shear fixture that cuts fasteners up to 6.3 mm diameter across two planes for NASM 1312-13 shear strength tests.
Brand: Universal Grip | Model: UGC-SF-120 | ● Configured to order
Double shear geometry for NASM 1312-13 fastener shear strength testing
Accepts fasteners up to 6.3 mm (about 1/4 in) diameter
Cuts the fastener across two shear planes in a single stroke
Hardened, nickel-plated steel block and blade hold their edges over long test series
No clevis required: the fixture sits between standard compression platens
Dimensional drawings and 3D models available on request
Standards: NASM 1312-13
Trusted by Global Companies


























Double shear testing of small fasteners to NASM 1312-13
The UGC-SF-120 is a compact double shear fixture for labs that qualify, accept or troubleshoot small fasteners: aerospace bolts, screws, dowel pins and clevis pins up to 6.3 mm (about 1/4 in) diameter. It follows the double shear arrangement of NASM 1312-13, where the fastener is supported on both sides of the loaded section and fails across two planes at once. Because the fixture works in compression, it drops into any universal testing machine that already runs with a pair of compression platens.
How it works
The fastener is passed through a hardened steel block. A central blade bears on the shank between the two support faces, and as the upper platen drives the blade down, the fastener is sheared on both sides of the blade simultaneously. The machine records the peak force, which is then evaluated as double shear strength in line with the standard.
Block and blade are hardened and nickel-plated. Sharp, stable shear edges matter in fastener testing: worn or rounded edges add bending to the shank and push results upward, so a hard working surface keeps lot-to-lot comparisons meaningful.
What you need to run it
The fixture has no coupling of its own and is placed between upper and lower compression platens, which are not part of the delivery. If your frame does not have platens yet, we supply compression platens sized to its load cell, plus any adapters needed for the machine connection.
Maximum load is confirmed on request. High-strength fastener alloys can reach double shear loads well beyond handheld or motorized force testers, so the fixture normally runs on a benchtop universal testing machine. Give us the fastener material, diameter and expected strength, and we will match the frame and load cell.
Typical applications
Lot acceptance and qualification of aerospace fasteners
Shear strength checks on screws and bolts
Dowel pin and clevis pin verification
Comparing materials, platings or heat treatments on one fastener geometry
Related fastener shear fixtures
For single shear to NASM 1312-20, see UGC-SF-010, the single shear fastener fixture. Tension-mode double shear of wires and rivets to EN 3238 is covered by UGC-SF-030 (double shear fixture for wires and rivets), and Amsler-type double shear of aluminum rod is handled by UGC-SF-020, the Amsler double shear fixture (see our ASTM B769 guide). The full range is on our shear fixtures page.
Send us the fastener diameter, material and your current platen setup, and we will quote the fixture with matching platens.
Double Shear Fastener Fixture NASM 1312-13 Specifications
TEST TYPE
Double shear of fasteners, compression mode
MAX. LOAD
On request
MAX. SPECIMEN DIAMETER
6.3 mm (0.25 in)
SHEAR PLANES
Two
MATERIAL
Steel, nickel-plated, hardened
COUPLING
None – placed between compression platens
TEMPERATURE RANGE
Ambient
SCOPE OF DELIVERY
Fixture; compression platens not included
STANDARD
NASM 1312-13
DRAWINGS
Dimensional drawings and 3D models on request
PART REF.
UGC-SF-120
Models & Options
Double shear fixture — For fasteners up to 6.3 mm; state the fastener diameter (Specify at order)
Compression platens — Upper and lower platens to suit your machine, ordered separately (On request)
Machine adapters — Connect the platens to your load cell and crosshead (On request)
What's Included
Double shear fixture: hardened, nickel-plated steel block and blade
Compression platens are not included – order them to suit your machine
Supported Test Standards
NASM 1312-13 — Fastener test methods – double shear test
Compatible Grips & Fixtures
Compression platens — Upper and lower platens the fixture runs between
Benchtop universal testing machines — Galdabini frames sized to fastener shear loads
Adapters — Couple platens to your machine's load cell
Bolt grips — Tensile testing of the same fasteners
Shear testing — Overview of shear test methods and fixtures
“Customer quote”
Related Equipment
UGC-SF-010 Single Shear Fastener Fixture NASM 1312-20
50 kN single shear fixture for aerospace bolts, pins and rivets, built to the NASM 1312-20 and MIL-STD-1312-20 Fig. 3a a
UGC-SF-020 Amsler Double Shear Fixture
Amsler-type double shear fixture for 10 mm aluminum alloy rod and bar to ASTM B769, with replaceable hardened dies and a
UGC-SF-030 Double Shear Fixture for Wires and Rivets EN 3238
Tension-mode double shear fixture for wires and rivets to EN 3238, with a split housing, central blade and knurled clamp
UGC-SF-110 Wood Shear Test Fixture EN 13354
5 kN compression shear fixture for wood and bonded solid wood panels to EN 13354, with a 10–60 mm adjustable jaw and Ø 2
Double Shear Fastener Fixture NASM 1312-13 FAQ
What fastener sizes does the UGC-SF-120 accept?
Fasteners up to 6.3 mm (about 1/4 in) diameter. State the exact diameter when you order so the fixture is set up for it.
Does it need a clevis or threaded coupling?
No. It works in compression and is simply placed between upper and lower compression platens, which are ordered separately.
What is the maximum load?
Capacity is confirmed on request. Share the fastener material and diameter and we will confirm the rating and recommend a universal testing machine to match.
Is this a single or double shear fixture?
Double shear: the fastener is cut across two planes at once. For single shear to NASM 1312-20, see UGC-SF-010.
Can I test rivets or aluminum rod with it?
It is designed for fasteners such as bolts, screws and pins. For rivet wire to EN 3238 use UGC-SF-030; for aluminum rod to ASTM B769 use UGC-SF-020.
What is it made of?
Hardened, nickel-plated steel, which keeps the shear edges sharp and protects the fixture from corrosion between test campaigns.




