Home › Products › Shear Fixtures › Bolt and Pin Shear Platens





Bolt and Pin Shear Platens
Clevis-mounted steel shear platens for single and double shear testing of bolts and pins in tension mode, with interchangeable hole sizes.
Brand: Universal Grip | Model: UGC-SF-200 | ● Configured to order
Single or double shear of bolts and pins, run in tension mode
Interchangeable shear platens with hole sizes made to your fastener
Spacer platen included to set the shear gap
Two opposing clevis holders with pin connection
Plain steel construction for routine incoming inspection
Hole sizes, capacity and coupling confirmed at quote
Standards: QVA-Z10-37-04
Trusted by Global Companies


























Simple shear platens for bolts and pins
The UGC-SF-200 is a straightforward shear set-up for mechanical engineering labs, incoming inspection and hardware suppliers who need to check the shear strength of bolts and pins without a standard-specific fixture. The bolt or pin passes through holes in steel shear platens that are mounted in two opposing clevis holders. As the machine pulls the holders apart, the platens slide past each other and shear the fastener.
Single or double shear
The platen stack decides the test. With one platen on each side, the fastener is cut on a single plane. With the outer platens on one holder and a central platen on the other, it is cut on two planes, which halves the load per plane and reduces bending in the shank. Tell us which configuration you need when ordering.
Platens and shear gap
The shear platens are interchangeable, with hole sizes made to suit your bolt or pin diameters, so one pair of holders covers a range of fasteners. A spacer platen is included to set the gap between the shearing faces; keeping that gap tight is what separates a clean shear failure from a bending failure.
Coupling and machine
Each holder connects by a female clevis with a Ø 60 mm (2.36 in) pin, a size typically found on larger frames such as floor-standing universal testing machines and hydraulic testing machines. For smaller frames, adapters or a different coupling can be supplied. Maximum load is confirmed on request, based on the fastener diameter, material and configuration. The platens are plain steel and intended for ambient-temperature testing.
Typical applications
Shear strength of bolts and pins
Fastener incoming inspection
Aerospace hardware checks
Mechanical engineering and design verification labs
Standard-specific alternatives
Where a test standard defines the fixture geometry, use a dedicated fixture: UGC-SF-010 for single shear to NASM 1312-20 or UGC-SF-120 for double shear to NASM 1312-13. For tensile testing of the same bolts, see our bolt grips, and browse all options on the shear fixtures page.
Send the bolt or pin diameter, single or double shear, expected maximum load and your machine coupling, and we will quote the platen set.
Bolt and Pin Shear Platens Specifications
TEST TYPE
Shear of bolts and pins, tension mode
MAX. LOAD
On request
SHEAR CONFIGURATION
Single or double shear, as specified
SHEAR PLATENS
Interchangeable, hole sizes on request
SCOPE
Holders, shear platens, 1 spacer platen
COUPLING
Female clevis, Ø 60 mm pin
MATERIAL
Steel
TEMPERATURE RANGE
Ambient
DRAWINGS
Dimensional drawings on data sheet; 3D models on request
PART REF.
UGC-SF-200
Models & Options
Shear platen set — Interchangeable platens with holes to suit your bolt or pin diameter (Specify at order)
Configuration — Single or double shear (Specify at order)
Spacer platen — Sets the shear gap; one supplied with the set (Specify at order)
Other couplings — Alternatives to the Ø 60 mm clevis for smaller frames (On request)
What's Included
2 opposing clevis holders
Shear platens with holes sized to your fastener
1 spacer platen
Supported Test Standards
QVA-Z10-37-04 — Shear test specification for bolts and pins
Compatible Grips & Fixtures
Bolt grips — Tensile testing of the same bolts
Floor-standing machines — Frames with large clevis couplings
Hydraulic testing machines — High-strength bolt and pin programs
Adapters — Fit the Ø 60 mm clevis to other couplings
Metals testing — Grips and fixtures for metals and fasteners
“Customer quote”
Related Equipment
UGC-SF-010 Single Shear Fastener Fixture NASM 1312-20
50 kN single shear fixture for aerospace bolts, pins and rivets, built to the NASM 1312-20 and MIL-STD-1312-20 Fig. 3a a
UGC-SF-120 Double Shear Fastener Fixture NASM 1312-13
Compression-mode double shear fixture that cuts fasteners up to 6.3 mm diameter across two planes for NASM 1312-13 shear
UGC-SF-190 Reinforced Concrete Shear Fixture DIN 488
Weld shear fixtures for reinforcing steel lattice girders and welded wire fabric, bar diameters 3–32 mm and capacities f
UGC-SF-210 Dispersion Adhesive Shear Fixture EN 1324
Shear adhesion fixture for dispersion and tile adhesives, rated to 20 kN, for EN 1324 Fig. 3, EN 12003 Fig. 3 and ISO 13
Bolt and Pin Shear Platens FAQ
Can I run single and double shear with the same set?
The configuration is set by the platen arrangement. Specify single or double shear when ordering so the platens are supplied to suit.
Which bolt and pin sizes fit?
Hole sizes are made to order. Give us your fastener diameters and we will size the interchangeable platens.
What is the spacer platen for?
It sets the gap between the shearing faces, which keeps the fastener in shear instead of bending.
What is the maximum load?
Capacity is confirmed on request, based on fastener diameter, material and single or double shear.
What coupling does it use?
A female clevis with a Ø 60 mm pin. Adapters or other couplings are available for smaller machines.
Do you have fixtures for specific fastener standards?
Yes, for example UGC-SF-010 for NASM 1312-20 single shear and UGC-SF-120 for NASM 1312-13 double shear.




