Home › Products › Wedge Grips › Steel Rope and Rebar Tensile Fixture





Steel Rope and Rebar Tensile Fixture – Conical Wedge Inserts
Modular holders with self-tightening conical inserts for tensile tests on steel wire rope, prestressing strand and steel or FRP rebar.
Brand: Universal Grip | Model: UGC-WG-010 | ● Configured to order
Conical wedge inserts close around round specimens as the load rises
Inserts for Ø 9.5, 12.7 and 15.2 mm (0.375, 0.5, 0.6 in) specimens; others on request
Reduction plates step the holder opening down from 84 mm to 38 mm
Dedicated inserts for 15.2 mm specimens with threaded ends
Side window for threading the specimen and checking the inserts
Holder versions rated 15 kN (3,372 lbf) and 300 kN (67,440 lbf)
Trusted by Global Companies


























Tensile fixture for steel rope, strand and rebar
Round, hard, helically wound specimens such as prestressing strand and wire rope are some of the most difficult items to hold in a tensile test. Flat jaws bite into the outer wires, and the break tends to happen at the grip instead of in the free length. The UGC-WG-010 takes a different route: tubular holders carry an insert carrier fitted with conical wedge inserts that wrap around the specimen and tighten as the load builds. The fixture handles steel wire ropes, prestressing strands, steel rebar and fiber-reinforced polymer (FRP) rebar.
How the insert system works
The specimen passes through the holder and seats in a set of conical inserts held in the insert carrier. As tensile force rises, the cone draws the inserts inward, so radial clamping grows with the load instead of being fixed at the start. A side window in the holder lets the operator thread the specimen and see that the inserts are seated before the test begins. Holders are nickel-plated steel and the inserts are hardened.
Holders, inserts and reduction plates
15 kN holder with large insert: for medium-sized specimens, with a female clevis for a 31.8 mm (1-1/4 in) pin
15 kN holder with reduction plate: the plate reduces the opening from 84 mm (3.31 in) to 38 mm (1.50 in) for smaller specimens
300 kN holder: carries the insert carrier and connects through a heavy clevis coupling
Strand inserts: for specimens of Ø 9.5, 12.7 and 15.2 mm
Threaded-end inserts: for threaded specimens of Ø 15.2 mm
Spiral specimen holder: a special holder for spiral specimens
Because inserts and reduction plates change inside the same holder, one fixture can cover several strand sizes and both plain and threaded ends. Inserts for other diameters are made on request.
Typical applications
Typical work includes testing steel wire ropes and prestressing strands, rebar tensile tests, threaded bars and anchors, and FRP bars used as non-corroding reinforcement. For steel products these are specimens for tests such as ASTM A931 for rope and strand, and ASTM A370 and ASTM A615 for reinforcing bar.
Machine fit
The 300 kN holder belongs on a Galdabini hydraulic universal testing machine or a heavy floor-standing frame, where capacity and stroke suit strand and bar breaks. The 15 kN holder is meant for smaller specimens on lighter frames. The machine coupling is confirmed at quote, and adapters are available if your crosshead uses a different pin or thread. The temperature range is on request.
Send us the specimen type and diameter, whether the ends are plain or threaded, the capacity you need and your machine coupling, and we will specify the holder, carrier and inserts. Request a quote.
Steel Rope and Rebar Tensile Fixture Specifications
MAX. LOAD
15 kN or 300 kN, depending on holder
TEST TYPE
Tensile
SPECIMEN
Steel rope, strand, steel or FRP rebar
SPECIMEN DIAMETER
9.5 mm, 12.7 mm, 15.2 mm; others on request
CLAMPING
Conical wedge inserts in insert carrier
HOLDER OPENING
84 mm; 38 mm with reduction plate
COUPLING
Female clevis, Ø 31.8 mm (1-1/4 in) pin (15 kN); heavy clevis (300 kN)
MATERIAL
Steel, nickel-plated; inserts hardened
TEMPERATURE RANGE
On request
PART REF.
UGC-WG-010
Models & Options
Name — Description (Part #)
15 kN holder, large insert — For medium-sized specimens (Specify at order)
15 kN holder, reduction plate — Opening reduced from 84 to 38 mm (Specify at order)
300 kN holder — With insert carrier and heavy clevis coupling (Specify at order)
Strand inserts — Specimens Ø 9.5, 12.7 or 15.2 mm (Specify at order)
Threaded-end inserts — Threaded specimens Ø 15.2 mm (Specify at order)
Spiral specimen holder — Special holder for spiral specimens (On request)
Inserts for other diameters — Made to your specimen size (On request)
What's Included
Holder in the capacity ordered (15 kN or 300 kN)
Insert carrier with conical inserts for the specimen diameter specified
Reduction plate where the smaller opening is required
Coupling as specified; adapters for other crossheads are available separately
Supported Test Standards
Compatible Grips & Fixtures
Hydraulic Universal Testing Machines — High-capacity frames for the 300 kN holder
Floor-Standing Testing Machines — Electromechanical frames for rope and bar tests
Adapters — Match the holder clevis to your crosshead
Bollard Grips — Alternative grips for wire, cord and rope
Metals Testing — Tensile setups for steel products
“Customer quote”
Related Equipment
UGC-WG-020 Heavy Duty Wedge Grip 600 kN
Non-shift wedge grips for high-strength plate, bar and rod up to 600 kN, with jaws for flat specimens to 50 mm and round
UGC-WG-030 Cryogenic Wedge Grip 20 kN
Stainless steel wedge grips for tensile tests in liquid nitrogen and liquid hydrogen, rated 20 kN at temperatures down t
UGC-WG-040 Compact Wedge Grip for Small Chambers 50 kN
A short, screw-actuated 50 kN wedge grip built to fit small test chambers and hot cells used for testing radioactive spe
UGC-WG-050 Mechanical Wedge Grip 600 kN
Enclosed, crank-operated wedge grip for high-force tensile tests to 600 kN on flat specimens up to 40 mm thick.
Steel Rope and Rebar Tensile Fixture FAQ
Which strand diameters do the standard inserts fit?
Ø 9.5, 12.7 and 15.2 mm (0.375, 0.5 and 0.6 in). Inserts for other diameters are available on request.
Can one holder handle large and small specimens?
Yes. The 15 kN holder takes a large insert for medium-sized specimens, and a reduction plate cuts its opening from 84 mm to 38 mm for smaller ones.
Can it test bars with threaded ends?
Dedicated inserts hold threaded specimens of Ø 15.2 mm. Tell us the thread and diameter if your bar or anchor differs.
Is it suitable for FRP rebar?
Yes, both steel and fiber-reinforced polymer rebar are listed applications. Send the bar diameter and surface profile so we can select the inserts.
What load ratings are available?
Holders are offered for 15 kN (3,372 lbf) and 300 kN (67,440 lbf). The 300 kN holder pairs with a hydraulic testing machine or a heavy floor-standing frame.
How does it connect to my machine?
The 15 kN holder uses a female clevis for a 31.8 mm (1-1/4 in) pin and the 300 kN holder a heavy clevis. Adapters cover other crosshead connections.




