Home › Products › Shoulder and Button Head Grips › XY Table with Hook Grip for Circuit Boards





XY Table with Hook Grip for Circuit Boards – Weld Pull Test
Compact XY table and twin 0.8 mm wire-hook grip for repeatable pull tests on laser-welded joints across a circuit board.
Brand: Universal Grip | Model: UGC-SH-040 | ● Configured to order
XY table brings each weld directly under the load axis before the pull
Upper grip with two hardened steel wire hooks, Ø 0.8 mm (0.031 in)
Fixed 9.7 mm (0.38 in) hook spacing for consistent load introduction
Compact 80 x 200 mm table footprint fits bench-top test frames
Test several weld positions on one board without remounting it
Female clevis coupling for a 15.9 mm (5/8 in) pin; others via adapter
Downloads and standards
Trusted by Global Companies


























Pull testing laser-welded joints on circuit boards
Laser welds on circuit boards are small, numerous and often spread across the whole board. Testing them one by one only gives useful data if every weld is pulled straight up along the load axis. The UGC-SH-040 combines a compact XY positioning table with an upper hook grip built for exactly this job. It is aimed at electronics manufacturers, weld process engineers and production QC teams.
How it works
The board is mounted on the XY table, which measures 80 x 200 x 93 mm (about 3.1 x 7.9 x 3.7 in, W x L x H). Using manual XY positioning, the operator moves the first weld directly below the upper grip. That grip carries two hardened steel wire hooks of 0.8 mm (0.031 in) diameter with a fixed spacing of 9.7 mm (0.38 in). The hooks engage the welded connection, the crosshead rises, and the joint is pulled in tension until it fails. The operator then shifts the table to the next weld and repeats, without unclamping the board.
Because the table sets the position and the hook spacing is fixed, each pull starts from the same geometry. That keeps scatter down and makes it easier to compare welds across a board, across lots, or before and after a process change.
Construction
XY table with manual positioning, 80 x 200 mm footprint
Upper grip with two hardened steel wire hooks, Ø 0.8 mm
Hook spacing 9.7 mm
Female clevis coupling for a 15.9 mm (5/8 in) pin; other couplings via adapters
The maximum load is confirmed when we quote, since it depends on the hook geometry needed for your joint. If your welds call for a different hook diameter or spacing, we can adapt the upper grip.
Typical applications
Weld process qualification, production quality control and failure analysis of laser-welded circuit board joints in electronics manufacturing. The same setup helps when comparing laser parameters, since each weld can be tested in a fixed sequence across the board.
Machine fit
Weld pull forces on circuit boards are usually low, so the fixture is normally mounted on a bench-top frame: a Mark-10 F-series motorized tensile tester or a small Galdabini bench-top universal testing machine. For peel-type tests on flexible circuits or tapes, see our peel fixtures.
Send us the board size, the weld layout, any hook geometry you need beyond the standard, and your machine coupling. Request a quote.
XY Table with Hook Grip for Circuit Boards Specifications
TEST TYPE
Tensile pull test of laser-welded joints
XY TABLE SIZE
80 x 200 x 93 mm (W x L x H)
UPPER GRIP
2 wire hooks, Ø 0.8 mm, hardened steel
HOOK SPACING
9.7 mm
COUPLING
Female clevis, Ø 15.9 mm (5/8 in) pin; others via adapter
MAX. LOAD
On request
OPERATION
Manual XY positioning
PART REF.
UGC-SH-040
Models & Options
XY table with twin hook grip — 80 x 200 x 93 mm table and upper grip with two Ø 0.8 mm hooks at 9.7 mm spacing (Specify at order)
Custom hook geometry — Different hook diameter or spacing for your weld layout (On request)
Coupling adapter — Adapter for machines without a 15.9 mm clevis (On request)
What's Included
XY positioning table, 80 x 200 x 93 mm
Upper hook grip with two hardened steel wire hooks
Female clevis coupling for 15.9 mm pin
Dimensional drawings and 3D models on request
Supported Test Standards
Standards list
Compatible Grips & Fixtures
Tensile testers — Mark-10 F-series motorized bench-top testers
Benchtop universal testing machines — Galdabini bench-top frames
Adapters — For other load cell and crosshead couplings
Peel fixtures — For peel tests on flexible circuits and tapes
Hook grips — Single hooks for loops and wire forms
“Customer quote”
Related Equipment
UGC-SH-030 Carpet Tuft Withdrawal Fixture ISO 4919
Bottom sample holder, loop hook and forceps for pulling single tufts from loop pile and cut pile carpets 2 to 9 mm thick
UGC-SH-050 Leather Double-Edge Tear Fixture ISO 3377-2
Matched pair of stainless steel hooks for double-edge tear strength of leather to ISO 3377-2, in 80 mm or 98 mm hook len
UGC-SH-020 Bottle Flip-Cap Test Fixture
A hinged hook lifts the lid of a flip-top cap through its natural arc while the bottle stays upright, recording opening
UGC-SH-060 Tire Cord Adhesion T-Test Grips ISO 4647
Slotted upper and lower grips that hold the rubber blocks of a tire cord specimen and pull the cord out to measure stati
XY Table with Hook Grip for Circuit Boards FAQ
What does the XY table do?
It lets you position each weld directly below the upper hook grip, so every joint is pulled along the load axis. You can step through several welds on one board without remounting it.
What are the hook dimensions?
Two hardened steel wire hooks of 0.8 mm (0.031 in) diameter, with a fixed spacing of 9.7 mm (0.38 in).
Can the hooks be changed for a different joint?
Yes. Tell us your weld layout and the hook geometry you need, and we can adapt the upper grip.
What is the maximum load?
It is confirmed at quote based on the hook geometry for your joints.
How does it mount on my machine?
The upper grip has a female clevis for a 15.9 mm (5/8 in) pin. Other couplings are handled with an adapter.




