ASTM D1876 Complete Guide: T-Peel Test Specimens, Speed, Grips and Peel Strength Calculation
ASTM D1876 is the T-peel test: two flexible adherends bonded face to face are pulled apart by their unbonded ends, so the specimen forms a T and the bond peels at a steady rate. It is the standard way to compare peel resistance of adhesives between flexible materials, from structural epoxies on thin aluminum to laminating adhesives on film and foil. The test is easy to set up and easy to get wrong. The peel angle is not fixed, so the result depends heavily on the adherends; the averaging window is defined after the initial peak, not over the whole trace; and the crosshead runs at 254 mm/min while the bond peels at half that. This complete guide covers the T-peel specimen and panel construction, adherend choice, preparation and conditioning, test speed, which testing machine to use (a Mark-10 tensile tester or a Galdabini universal testing machine), T-peel grips, why you do not need an extensometer (and where a video system still helps), the procedure, how to calculate average peel load from the trace with a worked example, D1876 vs. ISO 11339 and other peel tests, troubleshooting and a full FAQ.
For the standard reference page with fixture photos and downloads, see our ASTM D1876 T-peel test page. If one of your adherends is rigid, you need a fixed-angle peel instead; our companion ASTM D903 180° peel complete guide covers that test in the same depth.
ASTM D1876 at a glance
Full title: Standard Test Method for Peel Resistance of Adhesives (T-Peel Test). The current edition is D1876-08, reapproved in 2023 without technical change.
What it measures: the relative peel resistance of adhesive bonds between two flexible adherends, as average peeling load per unit width.
Panels: two flexible adherends 152 mm (6 in) wide by 305 mm (12 in) long, bonded over 229 mm (9 in) and left unbonded for 76 mm (3 in) at one end.
Specimens: 25 mm (1 in) wide strips cut from the bonded panels, with the unbonded ends bent apart at 90° to form the T.
Adherends: both must bend 90° without breaking. Clad 2024-T3 aluminum is the recommended metal adherend; fabrics, films and foils are also permitted.
Speed: 254 mm/min (10 in/min) crosshead, giving a peel-front speed of about 127 mm/min (5 in/min).
Result window: the average peeling load over at least 127 mm (5 in) of peel after the initial peak, divided by width.
Machine: test loads between 15 % and 85 % of capacity, with a continuous record of load against head movement or distance peeled.
Conditioning: 7 days at 23 ± 1 °C and 50 ± 2 % RH, unless the adhesive manufacturer states a shorter period.
Specimens per adhesive: at least ten.
Report: average, minimum and maximum peeling loads per specimen, the average peel resistance per width (N/mm or lbf/in) and the failure mode.

What ASTM D1876 measures and who uses it
In a T-peel test, neither adherend is held flat. Both arms bend away from the bond line as the crossheads separate, and the bond fails along a moving front where the two arms meet. The force needed to keep that front moving, per unit width, is the T-peel strength. Because it concentrates load on a line rather than spreading it over an area, T-peel is far more sensitive to adhesive toughness, surface preparation and cure than lap shear. A brittle adhesive and a toughened one can have similar lap shear strength and T-peel values that differ by a factor of ten.
D1876 is explicitly a relative test. The peel angle is set by the stiffness of the arms rather than by a fixture, and much of the work goes into bending them, so results depend on adherend material, thickness and temper as much as on the adhesive. Compare adhesives, primers, surface treatments and cure cycles on identical adherends; do not compare T-peel values made on different adherends, or treat them as a design property.
Structural adhesive suppliers and users in aerospace, automotive and industrial assembly use T-peel on thin aluminum to screen toughened epoxies, acrylics and urethanes, and to check surface preparation and cure.
Flexible packaging and converting labs use the T-peel configuration for laminate bond strength between films, foils and papers.
Textile, footwear and composites labs use it for laminated fabrics, coated fabrics, tapes bonded to themselves and other flexible-to-flexible bonds.
Quality labs use it as a fast, sensitive check of a bonding process, because surface contamination shows up in peel long before it shows up in shear.
The ASTM D1876 T-peel specimen
D1876 specimens are cut from bonded panels rather than bonded one at a time, which keeps surface preparation, bond-line thickness and cure consistent across the series.
Panel size: two adherends, each 152 mm (6 in) wide by 305 mm (12 in) long.
Bonded length: 229 mm (9 in), leaving 76 mm (3 in) of each adherend unbonded at one end. Use a release film or tape at the end of the bond so the boundary is sharp and straight.
Specimen width: 25 mm (1 in), cut from the panel after cure. A 152 mm panel gives several specimens once the edges are trimmed.
Tabs: the 76 mm unbonded ends are bent apart, each at 90° to the bond line, so the specimen looks like a T and each arm can be clamped.
Adherends: any combination that can be bent 90° without cracking. Clad 2024-T3 aluminum sheet is the recommended metal adherend, and 0.81 mm (0.032 in) is the thickness most labs use; check your edition and specification. Canvas, coated fabrics, plastic films and metal foils are also used, and the two adherends may differ.
Why the adherend matters so much
In a T-peel, part of the measured force goes into bending each arm through roughly 90° at the peel front, and with metal arms that bending is partly plastic. A thicker or harder adherend changes the bend radius at the front, the effective peel angle and the energy absorbed by the arms, so the same adhesive can give quite different T-peel values on 0.5 mm and 1.0 mm aluminum, or on 2024-T3 and a softer alloy. That is why D1876 values are only comparable on identical adherends, why the recommended aluminum construction is used so widely for adhesive data sheets, and why any change in adherend must be reported.
Symmetric and asymmetric specimens
When both arms are the same material and thickness, the T is symmetric and the bond line hangs roughly midway between the arms. When the arms differ, for example film bonded to foil or fabric bonded to thin metal, the stiffer arm bends less, the tail of the specimen tilts toward it and the peel front shifts. The test is still valid, but results are only comparable for the same construction. A common recommendation is to clamp the less flexible adherend in the moving grip. Report which adherend was in which grip.
Panel preparation, cutting and conditioning
Surface preparation: prepare metal adherends to a written procedure (degrease, abrade or etch, prime) as the adhesive manufacturer recommends. T-peel is very sensitive to surface preparation; a change in pretreatment shows up immediately.
Bond-line control: control adhesive quantity, bond-line thickness (shims, glass beads or a carrier film), pressure and cure. Measure and record bond-line thickness.
Keep the adherends flat: a pre-bent or kinked aluminum adherend peels unevenly. Handle panels flat and do not bend the tabs until just before testing.
Cut cleanly: use a shear, saw or router that does not heat, burr or delaminate the edges, and discard the outer edges of each panel. For films, fabrics and foils, a sharp blade or cutting die on an arbor press gives clean, consistent 25 mm strips.
Bend the tabs apart at 90° to the bond line without creasing the adherend at the bond boundary.
Condition for 7 days at 23 ± 1 °C and 50 ± 2 % RH, unless the adhesive manufacturer specifies a shorter period, and test promptly after conditioning in the same atmosphere where possible.
ASTM D1876 test speed and machine requirements
D1876 specifies a crosshead speed of 254 mm/min (10 in/min). As in any peel test where both arms are pulled apart, the bond line advances at about half the crosshead speed, so the peel front moves at roughly 127 mm/min (5 in/min). Keep that ratio in mind when you set the averaging window: 127 mm of peel needs about 254 mm of crosshead travel.
Constant speed under a fluctuating load: a motorized frame with closed-loop speed control. T-peel traces rise and fall continuously; the speed should not.
Load range: the standard requires test loads between 15 % and 85 % of the load cell or machine capacity. A 100 N peel on a 5 kN cell is 2 % of capacity, outside the rule; choose a cell of roughly 120 to 670 N instead.
Continuous record: load against head movement or distance peeled, stored in software so you can average a defined window. A maximum-load reading alone is useless for T-peel.
Data rate: high enough to capture peaks and troughs. A slow or heavily filtered signal smooths stick-slip and can bias the average low.
Travel: the 127 mm averaging window plus the initial peak takes roughly 270 to 300 mm of crosshead travel; peeling the full 229 mm bond takes about 460 mm plus the starting grip separation.
Which testing machine for ASTM D1876: Mark-10 or Galdabini?
T-peel forces are low, and the test needs a constant speed and a good trace rather than capacity, so it is a natural Mark-10 application. A Galdabini universal testing machine is the better choice when T-peel is part of a broader structural adhesive program or when you need testing at temperature.
Mark-10 tensile testers: basic and QC T-peel testing
100 lb (F105): 100 lbF (about 450 N) capacity covers most film, foil, fabric and many aluminum T-peel specimens, with the best resolution at low force. Standard speed range to 13 in/min (330 mm/min), so 254 mm/min needs no speed option.
300 lb (F305) and 500 lb (F505): for tough structural adhesives on aluminum, where the initial peak can be several hundred newtons, and for stands that also run lap shear.
Travel: the F105, F305 and F505 have 18 in (457 mm) of travel, enough for the 127 mm window after the initial peak but not always for peeling the entire 229 mm bond. The F755 and F1505 have 32 in (813 mm) of travel and 10 to 600 mm/min, so they peel the full bond with room to spare.
All F-series frames hold speed to ±0.2 % of setting and sample load at 5,000 Hz, so the stick-slip pattern of a T-peel trace is captured in full.

Fit a load cell that puts your average peel load and initial peak inside 15 to 85 % of capacity, and make sure your software can average load over a defined travel window after the peak. See Mark-10 test frame vs. universal testing machine for the full comparison, and every model on the tensile testers page.
Galdabini universal testing machines: structural adhesive labs
2.5 kN Quasar: single column, up to 1,000 mm/min and 1 m of stroke, enough to peel the full 229 mm bond with the open-front access that makes T-peel loading quick.
5 kN Quasar: dual column with 175 mm of column clearance, for an environmental chamber or wider grips.
10 kN Quasar: for labs that run T-peel alongside ASTM D1002 lap shear, D3167 floating roller and other structural adhesive tests on one frame.
UTM software lets you save a D1876 method at 254 mm/min, detect the initial peak automatically, average the next 127 mm of peel and report average, minimum and maximum loads per specimen and for the series. See the universal testing machine buyer's guide.
Choose a Mark-10 for production QC, laminate bond checks and adhesive lot approval at room temperature.
Choose a Galdabini UTM for structural adhesive development, qualification work, hot and cold T-peel from −80 to +280 °C, and labs running several adhesive standards on one frame.
Grips for ASTM D1876 T-peel testing
A T-peel test uses two grips, one on each arm, and the specimen hangs between them with the bonded tail free. Both grips must clamp the full 25 mm width squarely, without slipping, and with the arm centred on the load axis, so the peel front runs straight across the specimen. Our peel test fixtures and the peel testing applications page show T-peel setups.
Pneumatic grips
Pneumatic grips are the most common T-peel grip. Clamping force is set by air pressure, so every specimen is clamped the same way regardless of operator, and the jaws close square on the tab. Fast loading matters when you test ten specimens per adhesive. Our 2.4 kN centric and 2.6 kN pneumatic grips suit T-peel loads on aluminum, film and fabric; set the pressure high enough to stop slip but not so high that thin foil or film tabs are cut at the jaw edge.
Vise, roller and wedge grips
Vise grips: simple screw-action grips with serrated faces hold 0.81 mm aluminum tabs well at T-peel loads. Tighten both evenly so the arm is not clamped at an angle.
Roller grips: self-tightening eccentric grips for films, foils, coated fabrics and other slippery tabs. They clamp harder as the pull rises and need no air supply, which makes them a convenient choice on Mark-10 frames.
Wedge grips: mechanical wedge grips hold metal tabs securely and are convenient when the frame already carries them for tensile or lap shear work, though T-peel rarely needs their capacity.
Alignment and centering
Centre each arm on the grip axis, and both grips on the same vertical line. An off-centre arm makes one edge of the bond peel first, and the front runs diagonally.
Clamp close to the bend but not on it, and at the same tab length on every specimen, so the starting geometry repeats.
Let the tail hang free. Do not support or guide the bonded tail; in D1876 it finds its own position, which is part of what the test measures.
Remove slack without preloading the bond before you start.
Jaw faces at least 25 mm wide: serrated for aluminum, rubber-coated or fine-serrated for film, foil and fabric.
Adapters: our grips fit Mark-10, Instron, MTS, ZwickRoell, Shimadzu and Tinius Olsen frames with the right grip adapters; see the tensile grips page and the adhesive testing page. Our peel test fixtures guide compares T-peel with the fixed-angle methods.
Do you need an extensometer for ASTM D1876?
No. T-peel resistance is an average load divided by width. The standard asks for load against head movement or distance peeled, and crosshead travel gives both (distance peeled is about half the travel). There is no gauge length and no strain to measure, so a clip-on or long-travel extensometer has no role. You do not need an extensometer to comply with D1876.
A video system is still useful in a T-peel lab, for reasons that have nothing to do with strain:
Recording failure mode. D1876 results mean little without the failure mode: adhesive failure at one adherend, cohesive failure in the adhesive, or a mix. A video of the peel front shows where the mode changed along the bond and lets you match it to steps in the trace, which a single photo of the failed surfaces cannot.
Seeing the real peel angle. The T-peel angle is not controlled by a fixture. Video shows how the arms bend, whether the tail tilts toward a stiffer adherend and whether the peel front stays square, which explains a lot of scatter between constructions.
Spotting slip and zipping. A sudden drop in the trace can be grip slip or an unstable crack running ahead ("zipping"), typical of brittle adhesives. Video tells you which.
Testing in a chamber. A non-contact camera records the peel through the chamber window without opening the door.
If your lab already runs a video extensometer for tensile testing, use it to record T-peel tests as well. If peel is all you run, a camera with good lighting is enough to document failure mode. Read the video extensometer buying guide and types of extensometers before investing in a full system.

ASTM D1876 test procedure, step by step
Step 1: Prepare and bond panels to the adhesive manufacturer's procedure, with 229 mm bonded and 76 mm unbonded, and cure. Record bond-line thickness.
Step 2: Trim the panel edges and cut 25 mm wide specimens, at least ten per adhesive. Measure each width.
Step 3: Condition for 7 days at 23 ± 1 °C and 50 ± 2 % RH, or as the adhesive manufacturer specifies.
Step 4: Set the crosshead to 254 mm/min (10 in/min), fit a load cell that puts the expected loads between 15 % and 85 % of capacity, and zero the load with the upper grip installed.
Step 5: Bend the unbonded tabs apart at 90° to the bond line.
Step 6: Clamp one tab in each grip, centred and square, at a repeatable tab length, with the stiffer adherend in the moving grip if the arms differ. Let the bonded tail hang free and remove slack without preloading.
Step 7: Start the test and record load against crosshead travel continuously.
Step 8: Peel through the initial peak and at least 127 mm (5 in) of bond beyond it, about 254 mm of crosshead travel; peeling the full bond gives more data.
Step 9: Inspect both failed surfaces, record the failure mode along the bond and photograph it.
Step 10: Calculate average, minimum and maximum peel loads and the peel resistance per width for each specimen and for the series.
How to calculate average peel strength from a T-peel trace
Reading the trace
Take-up: the load rises as the bent tabs straighten toward the load line.
Initial peak: the bond resists until a peel front forms at the bond boundary, often giving the highest load of the test. D1876 excludes it from the average.
Peel region: the load settles into a band. Toughened adhesives give a fairly steady band with small oscillations; many adhesives give a saw-tooth stick-slip pattern; brittle adhesives can zip, with the load falling sharply as a crack runs ahead and then rebuilding.
End: the load falls as the front reaches the end of the bond or you stop the test.
Setting the 127 mm window
D1876 determines the average peeling load over at least 127 mm (5 in) of the bond line after the initial peak. Because the bond line moves about half as fast as the crosshead, 127 mm of peel is about 254 mm of crosshead travel. Start the window just after the initial peak has passed, and end it 254 mm of travel later or at the end of the steady region, whichever comes first. Use the same rule for every specimen and state it in the report.
Average: the arithmetic mean of all load points in the window is the usual digital equivalent of the standard's average peeling load. For strongly saw-toothed traces, some specifications also ask for the mean of peaks and troughs; ISO 6133 describes methods for analysing multi-peak traces.
Minimum and maximum: report the lowest and highest load within the window (and the initial peak separately if your customer wants it).
Peel resistance: divide the average load by the measured specimen width.
Units: N/mm (equal to kN/m), N/25 mm or lbf/in. 1 lbf/in = 0.1751 N/mm; 1 N/mm = 5.710 lbf/in.
Worked example
SI: a T-peel specimen of 0.81 mm aluminum bonded with a toughened epoxy measures 25.0 mm wide. The trace shows an initial peak of 210 N at 12 mm of crosshead travel. The window runs from 15 mm to 269 mm of travel (254 mm of travel, 127 mm of peel). Over that window the mean load is 98.0 N, the minimum 81 N and the maximum 117 N. T-peel resistance = 98.0 ÷ 25.0 = 3.92 N/mm, which is 3.92 kN/m, 98.0 N/25 mm, or 3.92 × 5.710 = 22.4 lbf/in.
Inch-pound: a 1.00 in wide specimen with an average peeling load of 22.0 lbf over the window has a peel resistance of 22.0 lbf/in, which is 22.0 × 0.1751 = 3.85 N/mm.
Series: ten specimens give 3.92, 4.35, 3.48, 4.21, 3.70, 4.06, 3.31, 4.18, 3.97 and 3.62 N/mm. The mean is 38.80 ÷ 10 = 3.88 N/mm (22.2 lbf/in), with a range of 3.31 to 4.35 N/mm, a standard deviation of about 0.34 N/mm and a coefficient of variation of 8.8 %. That is typical for T-peel on aluminum. If the two lowest specimens came from the same panel and showed bare metal on one side, the cause is surface preparation on that panel, not adhesive scatter.
Typical T-peel values
Treat these as rough orders of magnitude on 0.81 mm aluminum; adhesive data sheets and your own baseline are the real reference.
Brittle, unmodified epoxies: often below about 1 N/mm (under roughly 5 lbf/in), with zipping traces.
Toughened epoxies, structural acrylics and urethanes: commonly a few N/mm, around 3 to 10 N/mm (roughly 15 to 60 lbf/in).
Film, foil and paper laminates: usually a fraction of 1 N/mm, often limited by the strength of the film rather than the bond.
Precision and scatter
Treat D1876 as a comparative test, as the standard intends. T-peel results are sensitive to adherend thickness and temper, bond-line thickness, surface preparation, specimen width, tab bending and the averaging window, so values move between labs and constructions far more than the machine's accuracy would suggest. Coefficients of variation of 5 to 15 % are common within a well-run series. Test at least ten specimens from more than one panel, keep the window rule fixed, and do not compare values across labs or adherends without a correlation study.
T-peel testing at high and low temperature
Structural adhesive and laminate specifications often ask for T-peel at service temperatures, such as cold peel to check embrittlement or hot peel near the adhesive's glass transition.
Fit an environmental chamber around the grips; ours run from −80 to +280 °C. Let the specimen, tabs and grips reach temperature before testing.
Check chamber height and travel: the 127 mm window needs about 254 mm of crosshead travel inside the chamber, plus the grips and the hanging tail.
Use jaw faces and grips rated for the temperature, and a camera through the window to record the failure mode. See the temperature chamber buyer's guide.

What to report
The standard and edition, and any agreed deviations.
Adhesive (type, manufacturer, batch), adherends (material, temper, thickness, surface preparation) and which adherend was in the moving grip.
Bonding conditions, cure, bond-line thickness, conditioning and test atmosphere.
Specimen width, number of specimens, crosshead speed (254 mm/min) and the averaging window.
Average, minimum and maximum peeling loads for each specimen, the average peel resistance per width for each specimen and the series, in N/mm or lbf/in, with the traces.
The failure mode for each specimen (adhesive, cohesive or mixed), ideally with photos.
Common ASTM D1876 problems and how to fix them
Including the initial peak: it inflates the average. Start the window after the peak.
Window measured in peel instead of travel (or the reverse): 127 mm of peel is about 254 mm of crosshead travel. Set it deliberately.
Not peeling far enough: stopping before 127 mm of peel past the peak does not meet the standard; check your frame travel.
Comparing different adherends: T-peel depends on arm stiffness and yield. Compare adhesives only on identical adherends.
Kinked or pre-bent adherends: handle panels flat and bend the tabs only at the bond boundary, just before testing.
Arms off-centre: the front runs diagonally and the load rises. Centre both arms and align both grips.
Tab slip or jaw cuts: a falling plateau or a tab tearing at the jaw. Adjust pneumatic pressure, use roller grips for film and foil, or change jaw faces.
Load cell too large: peel loads below 15 % of capacity break the rule and lose resolution.
Adherend fails before the bond: foil or film tears at the front. Use a thicker adherend or back it, and report the failure mode.
Wrong speed: 254 mm/min (10 in/min). Faster or slower rates change the result for most adhesives.
ASTM D1876 vs. ISO 11339 and other peel tests
ISO 11339: the international T-peel test for flexible-to-flexible bonded assemblies and the counterpart of D1876. It runs at a slower crosshead speed (100 mm/min) with its own specimen and evaluation rules, so results are not interchangeable. See our ISO 11339 page.
ASTM D903: 180° peel of a flexible adherend from a rigid one at 305 mm/min crosshead (152 mm/min peel), averaged over the steady peel region. Use it when one adherend is rigid. Our D903 complete guide covers it.
ASTM D3167: floating roller peel. When one adherend is too stiff for a T-peel, the thin adherend is peeled around a free roller from the rigid one, giving a controlled angle.
ASTM D1781: climbing drum peel for sandwich panel facings, reported as peel torque per width.
ASTM D6862 and ASTM D3330: 90° peel of flexible-to-rigid bonds and peel adhesion of pressure-sensitive tapes.
ASTM F88: seal strength of flexible barrier packaging; its unsupported tail technique looks like a T-peel but is a different test for heat seals.
T-peel or 180° peel?
Use D1876 when both adherends are flexible and you want to compare adhesives or processes on a standard construction. Use D903 when one adherend is rigid, because the rigid member fixes the 180° geometry and the result reflects the bond more than the arm bending. When a structural bond has one thin and one thick metal adherend, D3167 floating roller peel is usually the better choice than either.
Related adhesive tests
ASTM D1002: lap shear of metal bonds, the usual companion to T-peel on structural adhesive data sheets. See the D1002 lap shear complete guide and lap shear vs. block shear.
ASTM D1062: cleavage strength of metal bonds; ASTM D897 and ASTM D2095: tensile (butt joint) strength.
ASTM D905 and ASTM D4501: block shear of wood and rigid plastic bonds.
Sandwich panels: ASTM C393 and ASTM C273; see the sandwich panel testing guide.
All methods on the adhesive testing page and the ASTM standards page.
Complete ASTM D1876 equipment packages
Basic QC T-peel station
Mark-10 F305 or F105 for low-force laminates, or an F755 when you want to peel the full 229 mm bond
A load cell sized so peel loads and the initial peak fall between 15 % and 85 % of capacity
A pair of vise grips for aluminum tabs or roller grips for film, foil and fabric, with grip adapters for your frame
A cutting die and arbor press for 25 mm laminate strips
Advanced structural adhesive lab
Galdabini 2.5 kN or 5 kN universal testing machine with automatic peak detection and window averaging
A pair of pneumatic grips with quick-change faces
Lap shear grips, floating roller and 180° peel fixtures from our peel fixtures range for the rest of the adhesive program
Environmental chamber for −80 to +280 °C and a video extensometer or camera to record failure modes
ASTM D1876 FAQ
What is ASTM D1876?
The ASTM standard test method for peel resistance of adhesives using a T-peel specimen. Two flexible adherends bonded over 229 mm are pulled apart by their 76 mm unbonded ends at 254 mm/min, and the average load per unit width after the initial peak is the T-peel resistance.
What is the ASTM D1876 test speed?
254 mm/min (10 in/min) crosshead speed. The bond line peels at about half that rate, roughly 127 mm/min (5 in/min).
What are the ASTM D1876 specimen dimensions?
Panels of two adherends 152 mm (6 in) wide by 305 mm (12 in) long, bonded over 229 mm (9 in) with 76 mm (3 in) unbonded, cut into 25 mm (1 in) wide specimens whose unbonded ends are bent apart at 90°.
What adherends does ASTM D1876 use?
Any flexible adherends that can bend 90° without breaking. Clad 2024-T3 aluminum, commonly 0.81 mm (0.032 in) thick, is the recommended metal adherend; fabrics, films and foils are also used, and the two adherends may differ.
How is T-peel strength calculated?
Average the peeling load over at least 127 mm (5 in) of peel after the initial peak (about 254 mm of crosshead travel), then divide by the specimen width. Report N/mm or lbf/in, plus the average, minimum and maximum loads for each specimen.
How many specimens does ASTM D1876 require?
At least ten per adhesive, ideally from more than one bonded panel.
Why are T-peel values different on different adherends?
Part of the force goes into bending the arms, so adherend thickness, stiffness and yield strength change the result. Only compare T-peel values made on identical adherends.
Can I run ASTM D1876 on a Mark-10 tester?
Yes. All Mark-10 F-series frames reach 254 mm/min. The F105, F305 and F505 have 457 mm of travel, enough for the 127 mm window after the peak; the F755 and F1505 have 813 mm, enough to peel the full bond.
What grips are used for T-peel testing?
Two matching grips that clamp each 25 mm tab squarely and centred: pneumatic grips for repeatable clamping, vise grips for aluminum tabs, and roller grips for film, foil and fabric.
Do I need an extensometer for ASTM D1876?
No. T-peel resistance is load per width, and crosshead travel gives the peel distance. A camera or video extensometer is useful for recording failure mode, the real peel angle and tests inside a chamber, but is not required.
What is the difference between T-peel and 180° peel?
A T-peel pulls two flexible adherends apart with no fixed angle. A 180° peel (ASTM D903) folds a flexible strip back from a rigid one at a fixed angle. See our D903 complete guide.
Is ASTM D1876 the same as ISO 11339?
They test the same configuration, but ISO 11339 uses a slower crosshead speed and its own specimen and evaluation rules, so results are not interchangeable.
Related reading
Get a complete ASTM D1876 system
Universal Grip supplies everything for ASTM D1876 and the rest of your adhesive program: T-peel and other peel fixtures, pneumatic, vise, roller and wedge grips, grip adapters, cutting dies and arbor presses for laminate strips, environmental chambers, video extensometers for documenting failure modes, and testing machines from a Mark-10 tensile tester to a full Galdabini universal testing machine. Tell us your adherends, expected peel loads and temperature range, and we will configure a compliant T-peel system and quote it. Contact us.




Comments